installing a new fire

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

dean baker

New Member
Jan 24, 2013
11
south wales uk
hi there i am looking to install a woodburner in an old chimney i have reopened.my first question is the opening is 40 inches wide of which i want to reduce by 4 inches each side with a concrete lintel accross the top of the opening just to tidy it up. brick work is fine its the old red clay bricks,now what type of brick do i use to reduce the width can i use any type of brick due to the heat also what type or mix of mortar,this is my first question i think i am going to get on your nerves in the next few weeks but many thanks in advance
DEAN
 
If you are going to install a stove it doesn't matter what bricks or mortar you use. Any brick mortar combo will be fine for that. If it was an open fireplace and the fire would be against the bricks special ricks and mortar would be needed. But use whatever.
 
Use the appropriate materials due to the fact that it may be used as an open fireplace in the future. Since I am taking a guess here that you are in the UK talking to a local building official or mason would help you determine what materials to use.
 
  • Like
Reactions: ScotO
thanks guys this fire will not be used as an open fire in the future so i can use normal brick with sand and cement mix,ok what are the clearances from the sides and rear of the stove as the materials are non combustible, and yes i am from south wales uk many thanks again for your replies below is a pic of the opening above the 2 rows of bricks there is a metal lintel with a brick arch above so i will be removing the 2 rows and will put a concrete lintel there which will be sitting on a row of bricks either side closing the opening roughly 9 inches leaving 27 inch wide and 27 inches tall 14 inches deep is this ok so far.

IMG00017-20130123-0640.jpg
 
  • Like
Reactions: ScotO
The stove manual should state clearances.

Understand that you will never use it for a fireplace but what about the family that buys the hous in 50 years?

Cool looking chimney - what is the rest of the house like? :)
 
hello mfglikman the problem is i have not chose a stove yet looking up on dimensions ,haha i have lived in this house for 20 years this was blocked up when i moved in the rest of the house is fine, this is my dining room (shes going mad) i understand what your saying about someone else owning the house in 50 years so i will do my best to pass on the info if i sell cos i aint counting on dying yet anyway cheers
 
I'd LOVE to see that fireplace in it's heyday, I bet it was a cozy place! If that were MY fireplace, I'd be cleaning off that whitewash parge and repointing all those bricks......then a good sealer (like Siloxane) to keep it clean and pretty..

A little catylitic stove would look great in there and really put out some heat, much more than an old open fireplace. I'd be considering installing an insulated liner for safety and performance reasons. Keep us posted with progress and pics, I love a good install project.....(check out mine on the link in my signature below).
 
i do remember this as an open fire place my wife lived here all her life so when we were courting we used to use the room with that fire blazing absolutely amazing this is why i wanted to open it back up much to her annoyance but we,re the boss aint we lads (oopps) and yes i have to use an insulated liner in there will keep you informed (probably get on your nerves) Dean
awesome project you did there scotty fair play i have a log cabin in my garden and thats having a fire put in as well but one job at a time hey.



just an update on the fire place it seems to be taking ages but we will get there
 

Attachments

  • IMG00028-20130202-0959.jpg
    IMG00028-20130202-0959.jpg
    212.5 KB · Views: 176
  • IMG00033-20130202-2215.jpg
    IMG00033-20130202-2215.jpg
    39.7 KB · Views: 169
Cute, that looks great. When do you get to fire it up?
 
IMG00076-20130212-1731.jpgIMG00076-20130212-1731.jpg
Cute, that looks great. When do you get to fire it up?
as soon as i have the liner fitted got to get a hetas qualified person to do it, regs hey.below is the register plate i made and the first course of bricks sitting on the angle iron their not cemented in yet though,now to get a piece of oak 5x4 inches by 6ft long,im a little lost on a fender around the hearth its 67 inches by 17 inches any help would be nice thanks
 

Attachments

  • IMG_0819.jpg
    IMG_0819.jpg
    87.8 KB · Views: 132
  • IMG00072-20130211-1723.jpg
    IMG00072-20130211-1723.jpg
    84.3 KB · Views: 156
  • Like
Reactions: Billybonfire
Hi Dean,
I would get some slightly oversize firerope and pack it in there, very easy to do, cheap and easy to remove if ever you have to.
Also pack it round the flue pipe/register plate gap.

hope this helps

Billy.
 
IMG00094-20130216-1706.jpg ok in the picture there are alcoves either side of firebreast walls where i have bricked should i come flush with the breast wall or not cheers
 

Attachments

  • IMG00093-20130215-1905.jpg
    IMG00093-20130215-1905.jpg
    150.1 KB · Views: 162
Looks good Dean. Stone veneer might work well above the mantel. Maybe a nice large mirror Trimmed out in nice woodwork. All depends on you & the lil woman's preferences. Many things can be done there.
 
I would just tidy up the plasterwork and paper/paint it, think you can over do it.

Billy.
 
Status
Not open for further replies.