I bought a Sooteater system a few week ago and the rain finally stopped long enough to let me climb up on the roof and try it out. I installed our new Jotul F600 woodstove at the end of February this year, so it didn't have too much use before the burning season ended. However, we did have an unusually cool spring, so we burned some clear into May.
Here are some before and after photos:
Before
After
And here is the rain cap before I took it down and cleaned it with a wire brush. As you can see from the photos I did not have much to clean. My chimney is around 17' tall, so I used all six of the three foot long rods. I have easy access to my roof and chimney, so I cleaned from the top down.
First, I took the top plate off my stove to give me access to the flue collar and connecting T. I left the T cap in place during cleaning. From inside the stove I stuffed a small pillow with a plastic bag over it into the flue collar opening to keep any soot, etc. from getting into the stove and house. This worked fine. I followed the instructions and connected all the rods together with the cleaning head and lowered the entire length into the flue. I then used my drill to spin the rods as I worked my way up the flue removing rods as I went. You have to be careful when you disconnect or connect rods together making sure you don't drop them down the flue pipe. I worked a good system out after a couple tries and things went well.
When I completed cleaning the flue pipe I took the rain cap down off the roof so I could clean it up as good as new with some wire brushes before putting it back in place. When I went to remove the cover on the bottom of the T connector inside my fireplace I could see right away I was going to have trouble getting the cap off. With the screws removed the cap did not want to budge and it is tight quarters working through a five inch gap between the stove and the sides of the fireplace opening.
Instead of fighting the cap I decided to just dip the creosote and soot ash out from the bottom of the T
from inside the stove. I used a small cup and lifted it into a trash bag I set on top of the baffle. I had an easy reach and this worked well. Once I had scooped as much as possible I finished up using a vacuum cleaner that has washable filters.
I was a bit surprised that I got as much creosote/ash as I did. I estimate about four cups came out of the 17' tall flue. I had burned well seasoned wood, but while I was getting to know my new stove I probably didn't burn some fires as hot as I should have. The Sooteater worked great and I'd recommend it to anyone who is cleaning SS liners. I did not try using it from the bottom up, so I can't comment on how it works in that direction. I got it online for about $43, which was less expensive than just buying fiberglass rods for a brush.
Here are some before and after photos:
Before
After
And here is the rain cap before I took it down and cleaned it with a wire brush. As you can see from the photos I did not have much to clean. My chimney is around 17' tall, so I used all six of the three foot long rods. I have easy access to my roof and chimney, so I cleaned from the top down.
First, I took the top plate off my stove to give me access to the flue collar and connecting T. I left the T cap in place during cleaning. From inside the stove I stuffed a small pillow with a plastic bag over it into the flue collar opening to keep any soot, etc. from getting into the stove and house. This worked fine. I followed the instructions and connected all the rods together with the cleaning head and lowered the entire length into the flue. I then used my drill to spin the rods as I worked my way up the flue removing rods as I went. You have to be careful when you disconnect or connect rods together making sure you don't drop them down the flue pipe. I worked a good system out after a couple tries and things went well.
When I completed cleaning the flue pipe I took the rain cap down off the roof so I could clean it up as good as new with some wire brushes before putting it back in place. When I went to remove the cover on the bottom of the T connector inside my fireplace I could see right away I was going to have trouble getting the cap off. With the screws removed the cap did not want to budge and it is tight quarters working through a five inch gap between the stove and the sides of the fireplace opening.
Instead of fighting the cap I decided to just dip the creosote and soot ash out from the bottom of the T
from inside the stove. I used a small cup and lifted it into a trash bag I set on top of the baffle. I had an easy reach and this worked well. Once I had scooped as much as possible I finished up using a vacuum cleaner that has washable filters.
I was a bit surprised that I got as much creosote/ash as I did. I estimate about four cups came out of the 17' tall flue. I had burned well seasoned wood, but while I was getting to know my new stove I probably didn't burn some fires as hot as I should have. The Sooteater worked great and I'd recommend it to anyone who is cleaning SS liners. I did not try using it from the bottom up, so I can't comment on how it works in that direction. I got it online for about $43, which was less expensive than just buying fiberglass rods for a brush.
And i think my cats went out early this year, I am embarassed to say how much creosote i got
