Fired by oil company 1 year after install

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
Haven't bought any oil for 3 years now.

House is warmer. Saving thousands a year.

We don't heat our basement. It is an old fieldstone basement and doesn't freeze. We do keep heat tape on the kitchen water pipes but we had to do that before with the furnace anyway because they are in a crawl space.

When we bought this house 17 years ago it was $25 a month on the budget plan for oil. The last time we put 100 gallons in our tank 3 years ago it cost $400 and we used 3/4 of it in one month.
 
Just had the greatest phone conversation. The oil company who I have had automatic delivery with for 12 years said I will no longer be on automatic due to low oil consumption.

Briefly - before installing my XXV last October my historical average oil use was 900 gallons a year. I have an oversized Raised Ranch 30x60 footprint with a finished basement. Heat and hot water with oil.

In the last 12 months I have used 300 gallons of oil prompting my oil company to make the call.

So I figure if I am eliminating 600 gallons a year.. $3.50 a gallon... $2,100 a year less in oil. I burned 3 tons of pellets last winter (furnace never was needed for heat.. just hot water) which cost me less than 900 with delivery. I saved $1,200. And my house was warmer than I have ever maintained it!!
Payback on the stove should be in 3 more years.

Had to share the news!!
My company grumbled as well. I guess they don't like coming to out to add 75 gallons (largest delivery) and certainly not the 35 gallons last time. The way I see it they make up for it with the neighbors, who spend approximately 4200 per year!
 
Bought 1750 galls 3 years ago.
Bought 1010 galls 2 years ago.
Bought 515 galls last year.
Have 100 gall left and plan on buying no oil this year.
The secret is Insulation, Insulation, Insulation. Plus a large pellet stove, a lot of wood and a HPWH.
The Heat Pump Water Heater saved 300 galls/year by itself.


Insulation and air sealing.
 
Two weeks after I installed my stove I knew I was not going to use as much oil. I called them to cancel my auto delivery. They did ask why and I let them know I was using alternative heat. At that time I did not know it would be my main heat.
 
Sounds great! I had the Nat Gas company out to "check my meter" after my first year burning.

Same thing happened to me, got 4 of them showing up at my door demanding to see the basement, they thought I had tapped into the line before the meter and was stealing gas. Mentioned something about shutting it off at the street and filing a police report if I didn't comply...
 
  • Like
Reactions: VIBErator and moey
Well they were not quite that aggressive, and actually when I explained that I started using my wood stove it was all good.
 
Our oil company actually now sells pellets as well.
 
  • Like
Reactions: raybonz
They can't fire you... you already quit!

Oil companies firing us is like a bartender firing a recovering alcoholic!

We are making our lives better by getting off oil...

Bill
 
Insulation and air sealing.

Correct. Insulation and air sealing.

Our house was built in the early 1800's and its been a long hard slog over 3 years.
But the oil use is like an annual report card on our progress.
It is great to see the hard work in $
 
  • Like
Reactions: Rastallama
Just had the greatest phone conversation. The oil company who I have had automatic delivery with for 12 years said I will no longer be on automatic due to low oil consumption.

Briefly - before installing my XXV last October my historical average oil use was 900 gallons a year. I have an oversized Raised Ranch 30x60 footprint with a finished basement. Heat and hot water with oil.

In the last 12 months I have used 300 gallons of oil prompting my oil company to make the call.

So I figure if I am eliminating 600 gallons a year.. $3.50 a gallon... $2,100 a year less in oil. I burned 3 tons of pellets last winter (furnace never was needed for heat.. just hot water) which cost me less than 900 with delivery. I saved $1,200. And my house was warmer than I have ever maintained it!!
Payback on the stove should be in 3 more years.

Had to share the news!!

Your story is very similar to ours!
Oil was at $4.20/gal (2008) when we ordered the p61. 24 X 32 Cape
Cut oil usage in half. You cut your usage by 2/3!!

Enjoy!!
 
My propane company calls me every two years or so to tell me that they are "coming for the tanks". We dont own the propane tanks and there is a minimum 150 gal order each year. To date I think we have use 150 gal in four years. We only use it for cooking.

If they ever do you can always get tanks filled at tractor supply they have good rates for small amounts. ( At least around me )
 
I have considered the possibility of an electirc heat pump water heater but have been told by some that switching to that would not really be saving much if any

Who ever told you is flat out WRONG. I have a heat pump HW heater (only use it in the summer when the heat it grabs is actually free) I cant detect it on my electric bill! I've said this before...I get my HW free during the summer. The electricity I use is offset by the electricity I don't use de-humidifying my basement. during heating season I use a HW maker on its own zone. I do believe using one of these during heating season could be counter productive as it robs heat from your structure.
 
  • Like
Reactions: moey
How were you heating your water with oil? I'm not an expert but I know there are several different ways to do it. When we moved into our home we had the tankless coil in the boiler heating our water but when that failed we switched to an indirect tank on it's own zone off the boiler. this method seems to be much more efficient than the coil. I have considered the possibility of an electirc heat pump water heater but have been told by some that switching to that would not really be saving much if any.


I did the same thing. I went with a two coil storage tank so I'm ready for solar panels to make DHW.
Electric rates are high here so oil actually comes out cheaper than electric, especially with a 87/92% efficient burner.
My burner is cold start so I can shut it off in the Summer ( what would happen if I get the panels on the roof ).
 
Just for some info for the OP - I had a wood/oil boiler, with a tankless coil for DHW, for 17 years until a year & half ago or so. Tons of hot water in the heating season from the wood, but in the non-heating season it was the most inefficient way there is to heat DHW, having to keep the boiler hot all the time. I figured we used about 150 gallons/year just for the months when we weren't burning wood. So 300 gallons for the whole year is certainlty believable if you have a similar setup. I would also get off that setup ASAP. I put in a new 80 gal. electric hot water heat a year ago. It uses about $30/mo (@ 0.16/kwh) in electricity for a family of 5. And I sent everything oil related in our house down the road - should have done it years ago. A heat pump water heater would be even better, especially if there are 'green' incentives in your area.

Question - I like the ideas of switching to Electric for DHW... but with a pellet stove and electric hot water I would not have any central heat for my house. I go back and forth with the idea due to that reason. Right now my DHW is a tankless coil in my furnace. I have considered putting in a separate tankless coil. Just don't know what to do for "the next step".
 
What do you have for an oil boiler now, how old is it, can it stand being turned off & left cold for extended periods of time, how often would backup heat actually be required, and what are other fuel choices for you? Natural gas? Any propane use already?
 
What do you have for an oil boiler now, how old is it, can it stand being turned off & left cold for extended periods of time, how often would backup heat actually be required, and what are other fuel choices for you? Natural gas? Any propane use already?

No natural gas/propane. My furnace is about 40 years old so its probably already on borrowed time. When I lose power for an extended period of time the seals in the boiler shrink and my floor gets saturated.

I'd only need backup heat when we were away if the winter but that doesn't happen very often.

I know I have to do something sometime in the near future...either:

1) install new furnace for DHW/backup heat (and rarely use furnace due to pellet stove but have it as backup)
2) Install electric or solar DHW, drain existing baseboard system and shut off furnace knowing if and when I turn it back on again it very well could not work. But I would have no central heat.. not a biggie in some ways but I know that if/when we ever sell I would have to probably install new furnace.
3) Install indirect boiler for DHW off existing furnace. Wouldn't help with furnace but would provide cheaper DHW that having the whole thing run only for water
4) ?

We have tossed this back and forth so many times I honestly don't know which way to go. FWIW... I can pretty easily install my own electric DHW heater and I have connections that would allow me to get furnace/indirect boiler installed at a pretty nice discount. Like 1/2 price.
 
Should have asked one more question - how much room do you have on your electric panel?

Anyway, since your boiler is old & likely on borrowed time (and your oil tank too?), and you don't use back up heat very often, and you have no gas options, I would get rid of the oil boiler and the oil tank and everything oil related, and replace it with a new electric hot water heater (or even better a heat pump water heater), and an electric boiler for backup heat. You will gain a ton of space and free up a chimney, and get rid of all the oil-related liabilities. That is very similar to what I did last year. I found a 2 year old electric boiler on Kijiji for $400 (with a circ pump), and new electric water heaters are not really that expensive. My new 80 gallon was less than $400. You will need assistance from an electrician, however.

Don't put anything permanent & big in the place where the oil boiler is now, in case you want to put a new one back in at some point in the future. The way I looked at it was, my oil stuff (boiler & tank) needed replacing anyway, so it had to go - bottom line. Plus it was costing me money to keep running. What I put in was cheap & easy (relatively), saves money on operating costs, and does what I need. If (when) the time comes that I will need more frequent backup, or I can't or don't want to handle wood any more or as much, I will see what the choices are at that time. With the way technology is advancing, if I had replaced now with a new oil unit, that might have left me in a bad spot when that time did come because there might be better choices then.

Might sound scary at first, throwing away the oil 'security blanket' - but once you cut the line it's all roses. ;)

(EDIT: And I don't think I could possibly bring myself to get rid of a good working hot water system - nothing beats that for heat).
 
300 gallons to heat your DHW for a year? I think I'd be doing something about that too.
now it is just a grossly oversized water heater and most likely short cyling like crazy. maybe a tankless or some sort of stand alone would help lower the his cost.
 
Should have asked one more question - how much room do you have on your electric panel?

Anyway, since your boiler is old & likely on borrowed time (and your oil tank too?), and you don't use back up heat very often, and you have no gas options, I would get rid of the oil boiler and the oil tank and everything oil related, and replace it with a new electric hot water heater (or even better a heat pump water heater), and an electric boiler for backup heat. You will gain a ton of space and free up a chimney, and get rid of all the oil-related liabilities. That is very similar to what I did last year. I found a 2 year old electric boiler on Kijiji for $400 (with a circ pump), and new electric water heaters are not really that expensive. My new 80 gallon was less than $400. You will need assistance from an electrician, however.

Don't put anything permanent & big in the place where the oil boiler is now, in case you want to put a new one back in at some point in the future. The way I looked at it was, my oil stuff (boiler & tank) needed replacing anyway, so it had to go - bottom line. Plus it was costing me money to keep running. What I put in was cheap & easy (relatively), saves money on operating costs, and does what I need. If (when) the time comes that I will need more frequent backup, or I can't or don't want to handle wood any more or as much, I will see what the choices are at that time. With the way technology is advancing, if I had replaced now with a new oil unit, that might have left me in a bad spot when that time did come because there might be better choices then.

Might sound scary at first, throwing away the oil 'security blanket' - but once you cut the line it's all roses. ;)

(EDIT: And I don't think I could possibly bring myself to get rid of a good working hot water system - nothing beats that for heat).
if he ever sells the house it needs central heat.
 
definitely. i'm shooting for 100 gals for supplemental heat and hot water for the year.
I got my "supplemental" oil usage down to 1000 gallons last year. !!! That was a 50% reduction over prior years, though.

Of course, I ain't spending a dime on pellets. :cool:

The secret is Insulation, Insulation, Insulation. Plus a large pellet stove, a lot of wood and a HPWH.
The Heat Pump Water Heater saved 300 galls/year by itself.
Insulation is a project we'll be tackling this winter, along with rebuilding and re-storming a half dozen windows each summer. I'm curious, what was your outlay for the HPWH? What size circuit does it require? We're really pushing the limits on our 200A service, and aren't entirely unhappy to continue running oil for DHW, as I figure it's not the worst thing in the world to keep the boiler in running shape with a little exercise.
 
No natural gas/propane. My furnace is about 40 years old so its probably already on borrowed time. When I lose power for an extended period of time the seals in the boiler shrink and my floor gets saturated.

I'd only need backup heat when we were away if the winter but that doesn't happen very often.

I know I have to do something sometime in the near future...either:

1) install new furnace for DHW/backup heat (and rarely use furnace due to pellet stove but have it as backup)
2) Install electric or solar DHW, drain existing baseboard system and shut off furnace knowing if and when I turn it back on again it very well could not work. But I would have no central heat.. not a biggie in some ways but I know that if/when we ever sell I would have to probably install new furnace.
3) Install indirect boiler for DHW off existing furnace. Wouldn't help with furnace but would provide cheaper DHW that having the whole thing run only for water
4) ?

We have tossed this back and forth so many times I honestly don't know which way to go. FWIW... I can pretty easily install my own electric DHW heater and I have connections that would allow me to get furnace/indirect boiler installed at a pretty nice discount. Like 1/2 price.

How big is your house? Maybe you could put in hydronic electric baseboard if your house is smaller. If you house is larger often a electric boiler while it sounds nice you violate electrical load requirements even if you have 200 amp service. Not good for resale in my opinion if you care about that. Id shy away from what may appear to be the cheapest solution. Get some quotes you may be surprised good and bad. We were in a similar bind with our central heat and ended up putting a geothermal system expensive to install but cheap to operate it ran about twice what a conventional system would be to install but I did a lot of the work myself.

Dont do #3 dont feed the pig, it will die and then youll have nothing.
 
I got my "supplemental" oil usage down to 1000 gallons last year. !!! That was a 50% reduction over prior years, though.

Of course, I ain't spending a dime on pellets. :cool:


Insulation is a project we'll be tackling this winter, along with rebuilding and re-storming a half dozen windows each summer. I'm curious, what was your outlay for the HPWH? What size circuit does it require? We're really pushing the limits on our 200A service, and aren't entirely unhappy to continue running oil for DHW, as I figure it's not the worst thing in the world to keep the boiler in running shape with a little exercise.

I doubt your pushing the limits of your 200amp service your probably pushing the limits of your panel which may need a sub panel unless your operating multiple electric stoves. Electric hot water heaters typically are 4500w or 5500w ( 30 amps ) same as a HPWH. You have to size for worst case which is pure electric.
 
Status
Not open for further replies.