burnt 'fleece' on stove..help...

is there a lot still on the stove. otherwise i think you could probably make a hot fire and scrape it off.

I'd vote for the acetone too but might have to finish with some very fine steel wool. Fine like 000 or 0000.

You may want to do a search. I vaguely remember this being discussed in the past. If not fleece, it was something else that melted to the box.

I'm afraid acetone won't cut it. Fleece is made from polyester (recycled soda & water bottles). From what I've been able to find, methylene chloride (the active ingredient in solvent based paint strippers) is the stuff to use. Of course, it is paint stripper, so unless your stove is enameled, it will strip the finish too.

regardless of what removes fleece, its melted, drastically changed the chemistry..... might remove it... might not depending on how burnt it is.... start with the solvent (I have had good luck with goo off, failing that, try acetone). if those dont work, then its mechanical means. you can buy plastic razor blades pep boys might have them, amazon does (apparently I cant post a link, search for "plastic razor blade" the one with best reviews was : Permatex 80189 Pro Scraper Plastic Scraper )

I have had great luck using a regular razor blade if you are very very careful, (super glue off of wood, silicon adhesive off wood, super glue off of my freezer after it glued shut....)

DONT BURN THE FIREPLACE until you remove it, I suspect it will only make it worse...

Might be obvious, but make sure the stove is COLD when you do it.

Likely PET , recycled soda bottles.
Acetone might craze the surface at best , methylene chloride or chloroform used to solvent weld might soften it but that would likely be like peeling a thousand layer onion.

If it melted on the stove it likely burned, won't soften again nor likely will a solvent soften it.

iirc, it melts at 425/450 and at 500 in the air it burns and turns black.


I'd work at it from the edges with a razor blade.

Wouldn't surprise me if it burnt its pretty much bonded to the paint.

porcelain enamel ?

I'd start with WD-40. It dissolves a lot of things I wouldn't have guessed. If it doesn't work, you're not out anything.

heat the fire box up, to approx 95f............. spray with wd40/, then scrape off with a plastic razor, then polish clean with wet paper towel....
thats just 2c worth..............k

I had the imprint of a tennis shoe on my glass and after trying unsuccesfully to scrape it off I just used the stove and eventually it burnt completely off. Don't know if your stove top will get hot enough though.

If your wife has nail polish remover (acetone), use that. It will take it off.

agree with pen, i'd be burning it off before I went the chem route

mking7,
I'm think that if this were my stove and i didn't want to damage the finish
in an area that shows i might duplicate the problem in an area that doesn't
show, maybe on the back side, and find my answer in a less obvious location.
Then proceed to the initial problem. This might save from damaging the finish
where you see everyday ?
rn

I don't think I would try burning any plastic inside my house. They give off some nasty, toxic fumes.

Been there. I had been warming the kids shirts before they put them on in the morning to go to school....they loved it. I did it typically when the stove was warming up. One morning I threw on a too-hot stove a synthetic shirt. Really, it was stupid, and it melted to the top more or less instantly. Mine is an enamel finish, and I figured it wouldn't hurt to leave it awhile. Next time the stove got really hot I swiped it off with a damp rag. Repeat if necessary.

My girlfriend looked at me with "that look" when I told her no synthetics on or too near the stove (she likes to warm her jamies and dry her clothes when they're wet). Maybe I should just send her this post rather than explaining the details.

Anyway, I'd leave it providing it isn't enough volume of material to offgas anything (too) toxic. It'll slowly remove itself.

Yeah, I knew way better than to do that on a stove that hot with even a cotton shirt, which probably would have scorched too. Like a lot of folks, I've gotten complacent about wearing synthetic shirts, like Under Armour, etc. If you ever get exposed to an accidental fire wearing one of those, your skin and that shirt will become "one." Horrifying to think about.

It also pays to remind the kids not to huddle too close to the stove. Even though all kids' jammies should have flame retardants in them, you don't want to ever have to test that. Plus, I'm less than convinced that the U.S. Products Safety Commission has any clue about what is, or isn't, in the products we import. Really, it is every man for himself anymore.