No Thermostat connection
- Thread starter Mabari99
- Start date
-
Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.
We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.
We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
- Status
You should be able to see the back of the control board by looking in the inside of the stove....may have to remove a cover? Usually the stat connections are on the rear of the board.
Here are some pictures of the back of the control board. Looks like a sealed unit to me, but the red wire at the top looks very like what John C posted in a previous picture. Could this be the stats jumper? I can't see the bottom because of the blower fan. But I think this might be the jumper and it looks like it is in place. And if so, does this mean this is NOT my problem?
Attachments
Even though the pic is blurry, I'll take a guess that it IS the stat jumper wire. If so, that's NOT your problem.
Actually the augur stops spitting out pellets and this causes the flame to go out.
SmokeyTheBear
Minister of Fire
The very first thing to do is to make sure that the connections on that jumper are tight and not oxidized because if they are loose or oxidized the controller will act like there is no jumper there.
If your damper is set for burning more pellets than are being delivered after a while there will not be enough fire in the burn pot to keep the POF (proof of fire) system closed this leads to the stove entering shutdown (auger stops, and so forth).
So after having verified the jumper is actually making solid contact I would then check and clean the POF system.
If your damper is set for burning more pellets than are being delivered after a while there will not be enough fire in the burn pot to keep the POF (proof of fire) system closed this leads to the stove entering shutdown (auger stops, and so forth).
So after having verified the jumper is actually making solid contact I would then check and clean the POF system.
Appreciate your advice very much. Yes the fans work perfectly fine, actually I am going to take your advice and change the air output pipe to fit the size of the stove, I don't know why they had that much reduction, I can only assume that the person who had the stove before me was even more ignorant of pellet stoves than I am. And I will have a go at cleaning the stove as you describe. Thanks so much.
Excuse my ignorance, but what is the POF system and how do I clean it? Will the instructions of Gary Gileau cover it?
From Smokey the Bear:
The very first thing to do is to make sure that the connections on that jumper are tight and not oxidized because if they are loose or oxidized the controller will act like there is no jumper there.
How do I do this, it is very hard to get at the back of the control panel?
The very first thing to do is to make sure that the connections on that jumper are tight and not oxidized because if they are loose or oxidized the controller will act like there is no jumper there.
How do I do this, it is very hard to get at the back of the control panel?
SmokeyTheBear
Minister of Fire
Do you have a manual for that stove?
POF is proof of fire normally it is a thermo disc stuck against the exhaust system (frequently called a low limit snap disc) it senses when the temperature in the exhaust system is at a certain temperature by closing. When the controller checks this switch and finds it is closed it sort of says hey great we have fire, exit start up mode, start the convection blower, and enter run mode. Some stoves have a thermo couple that serves this purpose, and some have a photo eye that actually sees the light from the fire in the burn pot. Your oil fired heating system if you have one also uses a photo eye as a proof of fire system
If your stove has a snap disc you remove it (always stove off, cold, and unplugged) and wipe it clean with a damp cloth. You can check it using a lighter or match and a continuity tester.
Usually it is more difficult testing a thermocouple but cleaning one is a simple operation of wiping with a cloth.
A photo eye can also be tested, once again cleaning it and any lens between it and the burn pot is a matter of wiping with a cloth.
POF is proof of fire normally it is a thermo disc stuck against the exhaust system (frequently called a low limit snap disc) it senses when the temperature in the exhaust system is at a certain temperature by closing. When the controller checks this switch and finds it is closed it sort of says hey great we have fire, exit start up mode, start the convection blower, and enter run mode. Some stoves have a thermo couple that serves this purpose, and some have a photo eye that actually sees the light from the fire in the burn pot. Your oil fired heating system if you have one also uses a photo eye as a proof of fire system
If your stove has a snap disc you remove it (always stove off, cold, and unplugged) and wipe it clean with a damp cloth. You can check it using a lighter or match and a continuity tester.
Usually it is more difficult testing a thermocouple but cleaning one is a simple operation of wiping with a cloth.
A photo eye can also be tested, once again cleaning it and any lens between it and the burn pot is a matter of wiping with a cloth.
- Status
Similar threads
