Hydronic Questions

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

Mtn Fire

New Member
Dec 12, 2011
20
New Mexico
Hello out there,

On a typical hydronic gasifier, how much powder or creosote is brushed out during an annual cleaning of the exhaust and heat exchanger tubes?

thanks in advance,

Alex
 
I clean the tubes monthly - after I clean the ashes from the lower firebox, I reach into the top access, bang each turbulator up and down a couple of inches to knock the ashes off and then scrape the base again. Usually not much ashes but worth doing. 2 or 3 times a year I get the brush out, but never run into creosote, so no big job. I clean the horizontal section of the flue a couple of times per year, but never find more than a thin coating of fine ash at the bottom.
 
I clean the tubes monthly - after I clean the ashes from the lower firebox, I reach into the top access, bang each turbulator up and down a couple of inches to knock the ashes off and then scrape the base again. Usually not much ashes but worth doing. 2 or 3 times a year I get the brush out, but never run into creosote, so no big job. I clean the horizontal section of the flue a couple of times per year, but never find more than a thin coating of fine ash at the bottom.

thank you,

Alex
 
My dad and brother are in the once a year club. Through the entire chimney there's maybe a gallon and a half of creosote. That's probably 30 feet out so of chimney.
 
A properly tuned and seasoned wood burning gasser produces no creosote, just a grey-black flyash. Creosote is an indication of something not correct or a lot of idleing.

TS
 
A properly tuned and seasoned wood burning gasser produces no creosote, just a grey-black flyash. Creosote is an indication of something not correct or a lot of idleing.

TS
I agree. I'm on my 5th season with my Tarm Solo 30, and I have yet to see any creosote in my chimney. I clean my heat exchanger tubes a handful of times each year, and all I get is fly ash. I've burned a fair share of softwood in my mix, too, but still no creosote.
 
Ok, i guess i call fly ash creosote. I get a little creosote in the firebox near the door, i open the door too often, its still new to me. Anyway, i clean out the secondary every burn or couple of burns and get about half a gallon of fly ash.
 
I run a brush through my horizontal tubes once a week as part of the regular cleaning cycle. Takes only a few minutes and I get maybe a cup of dry ash a week from the tubes themselves.
 
Hello out there,

On a typical hydronic gasifier, how much powder or creosote is brushed out during an annual cleaning of the exhaust and heat exchanger tubes?

thanks in advance,

Alex
Alex,

I clean my exchangers (eight of them) once a year and I get less then a soda can of residue out of them. I've never had creosote in my chimney. The only blockage I ever had was a starling that decided to fall down the chimney and wedge himself in there. After I put a "roof" on my chimney, I've never had anything to clean out. I hope my two cents help you.

Bob
 
Alex,

I clean my exchangers (eight of them) once a year and I get less then a soda can of residue out of them. I've never had creosote in my chimney. The only blockage I ever had was a starling that decided to fall down the chimney and wedge himself in there. After I put a "roof" on my chimney, I've never had anything to clean out. I hope my two cents help you.

Bob

Thank You Bob,

Alex
 
Status
Not open for further replies.