Trees coming down tomorrow.

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

bboulier

Minister of Fire
Feb 9, 2010
510
NE Virginia
These are trees at my son's new home.that are due to be removed tomorrow. There are several reasons for removal: (a) Foremost, safety. These are some hazardous trees. (b) Some will be removed for sheltering a garden and others are to be replaced with fruit trees. (c) Firewood!

The first picture shows a cedar, a maple, and a small cherry in back. The second shows a cherry (with several trunks in front) and a maple in the back. The diameter of the maple is about 3 ft. The final picture shows 2 trees. The big maple will get some trimming; the sassafras is destined for the woodpile.
 

Attachments

  • IMG_3055-web.jpg
    IMG_3055-web.jpg
    177.2 KB · Views: 210
  • IMG_3057-web.jpg
    IMG_3057-web.jpg
    184.2 KB · Views: 210
  • IMG_3059 web.jpg
    IMG_3059 web.jpg
    462.8 KB · Views: 208
Are you taking that down or leaving that up to the pros? Looks like a challenging job.
 
  • Like
Reactions: ScotO
Does he have a wood stove or will you get the wood?

More pictures tomorrow ? :)
 
  • Like
Reactions: ScotO
That's a lotta wood
 
No way I would take these down. They are really dangerous. Picture 3057 doesn't adequately convey the situation. The 3 foot in diameter maple lists at an angle of 45 degrees towards the neighbor's house. Some of the trees in 3055 are tilted towards the house.

I haven't been out to look at the results, but I know that the firm that was hired showed up with some "big" equipment. From all reports, things went well. My grandson, who is keen on construction equipment and chainsaws (since he has observed his grandfather using one) was excited.

I will post some pictures later in the week when I get time to visit.

Splitting is the next task. (Aside from shoveling some wood chips for mulch).
 
  • Like
Reactions: ScotO
OKAY, It's LATER IN THE WEEK, NOW......

Where's the pics?? ;)

Looking forward to some 'after' photos, myself!
The job was finished today, but I haven't been out yet. Will post pictures as soon I take some.
 
Finally got some pictures. I estimate this are about 6.5 cords - sassafras, cherry, maple, and cedar.

Sassafras

IMG_3089-rev-web.jpg

Mixture of cherry and cedar:

IMG_3090-rev-web.jpg

About 60% cherry and 40% maple with a little cedar thrown in:
IMG_3092-rev-web.jpg
 
Very nice, probably more wood than what the pictures can make it looks like. 6.5 cord would be just under 2 years for me!
 
Sean, The big pile by the shed is 4 rows of 18" deep and a couple of rows behind the shed. The pile on the right is 4 foot high in the middle, although it slopes down on the right hand side. It's possible I have over estimated. It could be as low as 5.3 cords. In any case, it's a lot of wood. A lot more than I am used to dealing with. This will be my son's first experience with serious wood splitting. He still has to put in a stove, but plans to do so. He has two fireplaces that can be used as places for installation.
 
Your probably right though, I went back and looked at the pics and that maple was huge! It's just hard for me to guess looking at piles of rounds.
 
Nice!
 
Bryan, you can be proud.
 
Sean, I misstated the number of rows by the shed. There are 6 rows of 18" pieces by the shed.
 
Nice, that looks like a lot of great wood!
If you don't have a splitter I'd rent one, splitting that much wood by hand will be quite the chore!
I know the Home Depot near me rents them.
 
Cross Cut Saw,

Still working out the splitting details. One possibility is to rent a big splitter - 20 ton or so. Dennis has put in a persuasive plug for a vertical one. However, the cost of renting the splitter and a pick-up truck to haul it may make a second alternative more attractive. The second alternative is to buy a smaller electric splitter and have a splitting party or two with a couple of my sons. The bigger rounds can always be split into smaller pieces for use on a low capacity splitter. The second alternative will be slower, but cheaper. If the wood were in my yard, I would surely go with the second approach. I don't mind whacking wood every day just for the fun and for the exercise. I will try and work out the costs of the big splitter alternative tomorrow.

Bryan
 
Cross Cut Saw,

Still working out the splitting details. One possibility is to rent a big splitter - 20 ton or so. Dennis has put in a persuasive plug for a vertical one. However, the cost of renting the splitter and a pick-up truck to haul it may make a second alternative more attractive. The second alternative is to buy a smaller electric splitter and have a splitting party or two with a couple of my sons. The bigger rounds can always be split into smaller pieces for use on a low capacity splitter. The second alternative will be slower, but cheaper. If the wood were in my yard, I would surely go with the second approach. I don't mind whacking wood every day just for the fun and for the exercise. I will try and work out the costs of the big splitter alternative tomorrow.

Bryan

Some one on here said HD will deliver a splitter,IDK call em, and I have seen on CL people renting out their splitters, and they deliver
 
Thanks for the suggestion. I will call around to see what I can arrange.
 
Looks like I am going to rent a 22-ton vertical splitter. That looks like the best way to go. Thanks for your suggestions.
 
Status
Not open for further replies.