Fun project!

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

EatenByLimestone

Moderator
Staff member
(And not insulation related!) :)

I had to move everything out of the kneewalls when I was working back there and one of the things I pulled out was my Grandmother's WWII era White Rotary 43 sewing machine and cabinet. The wife liked the looks of it and asked me to get it working. The last thing my Grandfather and Grandmother had said about it was that it was broken. They never said why, only that it was.

So I started playingwith it and it would turn over so I figured that was a start. It was loud and vibrated pretty badly though. A $2.77 bottle of sewing machine oil from Walmart quieted it down as I worked from one end to the other oiling as I found joints. I also pulled a lot of dust balls out of the 70 year old machine.

The only spot where I found anything wrong was in the bobbin area where there was a mess of thread wound up in there. After it was cleared I felt I was close to getting it to work right, but it just wouldn't do it for me. I couldn't figure out what the issue was and finally decided to try to use different thread when I read a blurb about thread and needle pairs in a offbrand manual made for Sears. I grabbed a few old bobbins and put one on the bottom and used the other on top figuring that they were the threads that my Grandmother used last. It worked! A nice clean stitch! Then I switched back to the old thread I was using and I ran into the same frustration that I had earlier.

Now I have to figure out how to ID the various different thread types to go with the one needle I have in a 70 year old machine. I can probably buy replacement needles, but then I'd have to figure out how to put them in.

So, the question is now why did my Grandparents both claim it was broken when it was some easily cleared tread caught up in it. Neither one was the type to give up on something like that. My only guess is with arthritic fingers my Grandmother got frustrated with it and told my Grandfather it was broken to keep him from bugging her about it. By this time my Grandfather couldn't see to clear it so it never got fixed.

The green angle? A cool sewing machine was brought back into service and we didn't have to buy a new one.

Here is an image of the same model, I need to take pics of mine, but haven't gotten around to it yet.

4042168727_43d4364615_z.jpg


Matt
 
That's pretty cool Matt. I wonder how much stuff gets discarded that only needs a small fix.
 
  • Like
Reactions: ScotO
Cool thread, Matt. On a separated note (not to sidetrack the thread), but aren't old machines (like your sewing machine) sexy looking? What ever happened to making stuff with some class. Most stuff from the bygone years had looks that will last forever........
 
  • Like
Reactions: brogsie
I bet a lot of it does. It takes a lot of time to figure out stuff when you have no idea how to troubleshoot it. I was getting pretty frustrated until I decided to try the old thread on the bobbins. I was pretty close to bringing it in to a repair shop to do some 20 second adjustment for $80 and make it all better.

I imagine if a person never really developed the skills to troubleshoot (like my wife for instance) they might be perfectly happy putting a plant on the cabinet and going to Walmart to buy a new machine that does 50 different stitch patterns. 49 of which they will never use.

Matt
 
I like the old machines. Most of my woodworking machines sport Art Deco styling. Heavy cast iron does wonders to cancel out vibration. It's often cheap too! I've never really had to do any major work other than lubrication, new belts, and removing rust on any of them. Maybe sharpening cutting edges, but that's more like general maintenance. I imagine that is the same for any machine made to actually do work.

Matt
 
  • Like
Reactions: PapaDave and ScotO
I like the old machines. Most of my woodworking machines sport Art Deco styling. Heavy cast iron does wonders to cancel out vibration. It's often cheap too! I've never really had to do any major work other than lubrication, new belts, and removing rust on any of them. Maybe sharpening cutting edges, but that's more like general maintenance. I imagine that is the same for any machine made to actually do work.

Matt
Yessir.....stuff nowadays is made to break or throw out after some service. Take for instance my newer Craftsman table saw.....almost all plastic with an aluminum table. Cheesy at best. My WWII Craftsman table saw is heavy duty, cast iron table and motor mount, etc. Built to take a POUNDING. It will long outlast that newer one....

Same for my antique lathe.......and they look way cooler than the new stuff, to boot.
 
  • Like
Reactions: brogsie
Ahh, somebody I can post pics of old 'arn for! :)

I used to love going to estate sales when I had the time.


http://i167.photobucket.com/albums/u124/EatenByLimestone/IMG_1692.jpg

http://i167.photobucket.com/albums/u124/EatenByLimestone/IMG_0746.jpg

Odd vise/anvil/drill designed and made by the guy who designed the high lift jack. I've since restored this, but I need to do it again since I screwed up and used lacquer while trying to replicate japanning. http://s167.photobucket.com/user/EatenByLimestone/media/IMG_0647.jpg.html?sort=3&o=107

http://i167.photobucket.com/albums/u124/EatenByLimestone/P4110118.jpg

I should stop now, I could go on for hours like this. I have too much crap.

Matt
 
  • Like
Reactions: ScotO
My wife has more than half a dozen old black Singer machines around the house. One belonged to her 80+ year old mother, or my wife's grandmother (don't recall how that story went). At least 2/3 of them will stitch vinyl and leather if you ask them to. No plastic gears, all metal parts, and beautiful machines if you take the time to clean them up (as my wife has done to several).

My wife pointed out something about the White you have when I showed her the photo and read her your story: she said many of her old Singer machines only like OLD bobbins. She said newer bobbins routinely foul up some of the old machines. She said the bobbins may look alike, but there is something slightly different about them. If that bobbin that gave you grief gives you grief with different thread, it might be the bobbin's fault, not the thread.

Having just finished sewing my first boat cover over the weekend on my father's industrial sewing machine, I will suggest removing your needle and finding replacements before you break the one you have. It's much easier to find replacements when you have one, then when you have pieces. I went through 3 needles sewing the boat cover for my 15' Boston Whaler. I blame part of that on being a novice seamstress. (My dad is a novice seamstress as well, but he has such a collection of boats that having them all fitted with covers and tops was getting so expensive that he decided to buy an industrial machine [Sailrite] to make his own stuff).

Hope you enjoy the machine. My wife and I have a collection of art deco "retro" small kitchen appliances. They are mostly chrome, made in USA, and still work 40-50 years later.
 
Good point on the needle. I'll have to pull it out before we really start using the machine.

Thank you,
Matt
 
We have an old Singer of that vintage. My wife does use it sometimes. She would use it more but all it does is straight stitch.She only uses that one when she sows my work jeans or my Carharts. There are still quite a few of the old Singers as they made a lot of them.
 
  • Like
Reactions: PapaDave
I've got a singer of that age in the tie-up of my barn....
 
Yessir.....stuff nowadays is made to break or throw out after some service. Take for instance my newer Craftsman table saw.....almost all plastic with an aluminum table. Cheesy at best. My WWII Craftsman table saw is heavy duty, cast iron table and motor mount, etc. Built to take a POUNDING. It will long outlast that newer one....

Same for my antique lathe.......and they look way cooler than the new stuff, to boot.

We've got a newish (last 5 years or so) craftsman table saw at work.... AL table.... what a POS.... I had to fabricate a stand for it (it has legs) to keep it from tipping over while ripping a sheet of plywood. *My* table saw is the ubiquitous 10" craftsman belt drive.... iron table... I love that saw.... (The bessemeyer fence doesn't hurt). the only thing I wish it has was a dual voltage motor like my dad's 10" belt drive...
 
  • Like
Reactions: ScotO
I make do with a Dunlop 8" tilt table. I try not to break down sheet goods. I have a couple friends with unisaws and such that I can use also. When I finally get the inside of this house done I'll be able to focus on putting a shop together again.

Top.jpg


The miter gauge walked off when I was trying to sell the house that the saw was sitting in. Grrrrr....

Matt
 
unisaws are awesome... if you've got big enough wire in the shop to start that big baldor motor....
 
The garage is the future site of the shop. I ran a sub panel out into it so it will be a quick and easy wiring job. I have it set up mostly for hand tools, but ran a double box every 4 feet down the wall where the tools are. Each set of outlets in the double box is on its own circuit so I could run something like a router and task lighting from the same spot. It's nice when I need heat out there also. I can set a space heater on the bench right beside me.
 
Status
Not open for further replies.