Problem with feeder rate on a Englander 25-PDVC

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
Coyote_nb_ca

Coyote_nb_ca

Member
Dec 21, 2012
52
Carlingford NB Canada
www.schwanewede.ca
hi,

we have a small prob with our Englander 25-PDVC

on feeder rate he use ca 50lb of pellets/day.. that's a lot to match and he overheat the Area where he is sitting.

is there a way to reprogram the feeder settings to a lower amount ??

this video and the pic is made at the end of the startup
http://www.schwanewede.ca/stove.mp4
this picture is made on setting 1 - 3 !!! the fire will be some bigger 10 min later

DSCF2525.jpg

any suggestion to reprogram the feeder ??

thx
fred
 
What is the 3 bottom buttons set at? Factory is 641
 
thx

jep that's what the stove give back

but it's to match

is there a way to lower the feeder rate ???
 
Start the stove with bottom bottoms on 641 heat setting on 5 fan on 5 when fire is burning and convection fan turns on move heat on 1 fan on 1 set bottom buttons at 461 that will slow feed rate.
 
the stove is on 641 and it runs on 1 1

but it's to hot :(
 
Do what I said in my last post move bottom 3 numbers to 461 in other words change the low fuel feed button to 4 and run it on 1 1...if you need more heat change back to 641 and move your heat and fan button to desired comfort level.
 
I don't know why your your low burn air is 4, it should be 6
 
sorry i need to clean my glasses ....

will do this when back at home
 
Did you ever change your mode c or d?
 
I was given those directions by ESW last year because I was being cooked out in warmer weather, it works
 
no never i don't know how to change the 641 settings
 
You can also try 3 on low fuel feed but don't go lower than that try 4 for a while and try it
 
Press the lower left button ( low fuel feed) the # 6 should come up press arrows to adjust same for low burn air
 
If you didn't change your mode then don't worry about it, it should be factory...we can deal with that later if what I said don't work.
 
thx have my girl on the phone and she try it
at the moment 341
will monitor the fire now and mybe set back to 441

thx
fred
 
I still would change the middle # to 6 (low burn air). Keep it on 1 1. Yep play with 3 or 4 on your low fuel feed I'm sure you will get close to the results you are looking for.
 
Just remember if you change the heat range above 1 move your low fuel feed back to 6
 
I must be having a brain fart, low burn air should be 4 not 6 you were correct...run 441 or 341 sorry about that.
Denny
 
Hi,

we running now on 541 and we are fine with it.

thx for you help.
fred
 
Status
Not open for further replies.

Similar threads

K
Deep clean Englander 25 PDVC exhausts into chimney?
Replies
3
Views
1K
The Pellet Mill - Pellet and Multifuel Stoves
Rascal08
R
F
Power wattage of a Englander 25-pdvc for battery back-up calculation.
Replies
3
Views
2K
The Pellet Mill - Pellet and Multifuel Stoves
Fraulein
F
M
Englander Low Fuel Speed
Replies
0
Views
2K
The Pellet Mill - Pellet and Multifuel Stoves
MaloneJ9495
M
0
New Englander pellet stove 25-pdvc, Flame to tall?
Replies
22
Views
3K
The Pellet Mill - Pellet and Multifuel Stoves
Rneal55555
Rneal55555
P
Englander 25-PDVC not working, No Codes
Replies
3
Views
1K
The Pellet Mill - Pellet and Multifuel Stoves
ericofmaine
ericofmaine
Top Bottom
Back