Should A Constantly Running Modulating Pellet Boiler Be A Goal?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
velvetfoot

velvetfoot

Minister of Fire
Dec 5, 2005
10,202
Sand Lake, NY
Is getting a modulating pellet boiler to run almost constantly good for it? At a minimum 30% power level and with the buffer tank, I can see there being long stretches during the winter where it might never shut down. I think the BioWin cleans itself as it runs, so it wouldn't have to shut down for that.

I understand that creosote shouldn't be a problem, but does it run more efficiently at 30% (the specs in the install manual seem to indicate that)? How about wear and tear: Is it made for this constant duty?

I can see fewer startup emissions and having the boiler at the ready to supply a zone is also great.

(Edit: Marc tells me that it shuts itself down every 6 hours for a few minutes to cool down.)
 
Last edited:
Yes, long run times and infrequent start/stops are very desirable from an efficiency stand point and a equipment wear and tear standpoint. The boiler should handle the long run times no problem. Yes, it is likely that the efficiency is higher at lower output because the heat exchanger (boiler tube surface area) is large compared to the heat output at high fire. Even with a widely modulating boiler, however, there will be times when your load is very low (this time of year, for example) and the boiler will need to shut off. A buffer tank is especially useful for that.
 
Regarding wear and tear, seems to me if you need a certain amount of BTUs from the boiler in a day, assuming the efficiency is the same at different modulation rates, it will have to auger the same amount of pellets, blow the same amount of combustion air, and auger out the same amount of ash. Only the rate differs, but the number of motor shaft rotations should be about the same.

Maybe the more frequent thermal cycling is the biggest wear component.
 
Deering said:
Regarding wear and tear, seems to me if you need a certain amount of BTUs from the boiler in a day, assuming the efficiency is the same at different modulation rates, it will have to auger the same amount of pellets, blow the same amount of combustion air, and auger out the same amount of ash. Only the rate differs, but the number of motor shaft rotations should be about the same.

Maybe the more frequent thermal cycling is the biggest wear component.
Click to expand...


Actually I was thinking mostly about the ignitor, but I think it is fair to say that any piece of equipment has an easier time of it when running at steady state than when frequently cycling on and off.
 
That's how I run mine but your system has to be set up for it by using constant but metered flow to your heat emitters.

Right now we are at 24* with about a 10 mph west wind. I have the temp setpoint at 149* in the boiler and it is firing at 34% output. Boiler size is the 210 so it's producing roughly 24,000 btu's/hour. As outdoor temp drops I'll raise the water temp in 5* increments when i notice the house dropping below it's normal 73*.
 
I think there's a 0-10 v. thermostat connection on the board in my unit? Nothing fancier. Is that something that an outdoor or indoor reset could tap into? Not that I would, with my emitters, tank, etc.
 
Status
Not open for further replies.

Similar threads

I
Help! Restoring a Deeze Freeland Flame stove
Replies
1
Views
202
The Pellet Mill - Pellet and Multifuel Stoves
jjam
J
U
Pellet Boiler Windhager BioWin2 262 install
Replies
8
Views
2K
The Boiler Room - Wood Boilers and Furnaces
Unextinguished
U
H
Enviro Empress FS Pellet Stove - Vacuum code resolution in step by step detail
Replies
1
Views
485
The Pellet Mill - Pellet and Multifuel Stoves
johneh
johneh
Max W
Minisplits and wood
Replies
4
Views
871
The Inglenook
EbS-P
EbS-P
O
Help with optimal running my EPA stove
Replies
5
Views
1K
SBI: Century,Drolet,Osburn,Valcourt,Englander
EbS-P
EbS-P
Top Bottom
Back