Totally Useless Observation

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

BrotherBart

Modesterator
Staff member
But when I did it a few years ago a couple of folks appreciated it.

20 degrees out this morning with 20 mile an hour winds after down to 11 at sunup. Needed to look at the liner so I stuffed the IR thermo in my coat pocket and went up to check the uninsulated liner in the double flue mass of bricks chimney.

Stove was at 504 going up and coming down. Top of the 21 foot liner was 328 degrees. Last time I did that years ago the stove was at 400 and the liner up top was 235. Anything over the boiling point of water, around 228, is fine with me.

Like I said, useless info. I know, insulate the liner and it would be 10,000 degees at the top. >>
 
  • Like
Reactions: blacktail
Seen a few of yours where I thought the same thing. ;lol
 
Good man my friend. Keep doing what you do. Only pro sweep on the site these days.

But I still ain't gonna bust out those tiles.
 
And that is fine we will do it when it makes sense lol.
 
  • Like
Reactions: Swedishchef
For the life of me I have never been able to figure out what a thermometer 18" up from the stove could tell me about what is happening 21' up. Or any feet up for that matter.

I consider the things about as informative as, well can't think of anything.
 
I know, insulate the liner and it would be 10,000 degees at the top. >>
Hey, I think at that temp one of those heat-robbers would actually work! ;)
never been able to figure out what a thermometer 18" up from the stove could tell me about what is happening 21' up. Or any feet up for that matter. I consider the things about as informative as, well can't think of anything.
It may not tell you what's going on above it but it tells you what's going on below it. I can use one to tell me when to close the bypass on a cat stove (run flue temp at X degrees for X min, close bypass and get guaranteed light-off about every time. The same would work on a tube stove, I'd imagine...
 
If you are measuring your flue temperature near the exit and it is above 220ºF it is telling you that your chimney is probably safe. With a few more parameters for a correlation it might actually help someone else.
 
OH MY GOODNESS. Uninsulated liner in a brick chimney with the tile in place. The horror. And to think I thought you knew a thing or two about wood burning. ;)
 
  • Like
Reactions: RevJim708
Between him and webby3650 there's lots of knowledge passed around.

You bet. I figured saying he was the only pro sweep would have gotten a rise out of webbie3650. ==c

Here is a pic of webbie3650.

bholler.jpg
 
  • Like
Reactions: Osagebndr
Yanking your chain webbie. Yanking your chain.
 
  • Like
Reactions: webby3650
This thread has inspired me to go out today and get the ladder and IR gun and get up on the roof.

I just need to shovel 18 inches of snow and ice off first.;lol

On second thought, maybe just another cup of coffee and a few minutes in front of the stove will suffice.




( I wonder how accurate the IR gun would be from 22 feet below) ???;)




.
 
Anything over the boiling point of water, around 228, is fine with me.
228? Is that new math, last I checked BP was still 212*. Been a couple years since I have checked though...>>

You just checkin to see if anybody in the class is actually paying attention?! ;lol
 
  • Like
Reactions: Big papa
"Totally useless observation" they remarked as they boarded lifeboats off the Titanic...
 
Pure water, 212 at sea level.

I don't have a beach in front of the house. And ain't so sure the water in the wood is pure.
 
You bet. I figured saying he was the only pro sweep would have gotten a rise out of webbie3650. ==c

Here is a pic of webbie3650.

View attachment 152292
Where on earth did you find that picture of me? It's a good shot, that's for sure!

I do much more than sweep flues. I get to be part of the entire install of chimneys, stoves, fireplaces, liners. The whole 9 yards. It's a different scenario everyday.

I love what I do and enjoy sharing it with others.
 
  • Like
Reactions: jeff_t
This is Glenn Holler when he was training bholler.

ben and glenn chimney sweeps.jpg
 
Pure water, 212 at sea level.

I don't have a beach in front of the house. And ain't so sure the water in the wood is pure.
Unless you live in New Orleans your boiling point would be lower, not higher. Good point on the "water purity" though

My chart shows
1k ft elevation = 210.1*
2k = 208.1
3k = 206.2
 
Went through this whole drill six or seven years ago when I posted on this subject. Boiled three samples of our tap/well water with three different heat sources and using three different thermometers. All started boiling between 225 and 230.

So I use 228.
 
  • Like
Reactions: Hickorynut
You think these kind of posts are going to get me back on the boards?
smiley-taunt013.gif
 
Status
Not open for further replies.