Trying to make an old log splitter new again

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

McKraut

Feeling the Heat
Sep 1, 2011
341
South Central PA
I bought and old Central Tractor log splitter (20 years plus) that I want to fix up and use this winter. I have completely disassembled the splitter and am trying to clean it up. When I pulled the suction line from the hydraulic tank and drained the oil, I found a lot of junk coming out of the bottom of the tank (it looks like rust and/or paint). As far as I can tell the filter had been replaced (at least once) but I could not get any history on the splitter. I drained all the transmission fluid out, and I want to clean out the reservoir. What would be the best way to clean or flush this out?

Thanks for your help,
Bob
 
I would flush it several times with diesel.
 
  • Like
Reactions: Fifelaker
I have no experience with this, but I was wondering if I could use very hot water, soap, and high pressure water. Fill the tank with hot water and soap, agitate it, drain it, and rinse it. Is this practical or am I creating more problems for myself?
 
I have no experience with this, but I was wondering if I could use very hot water, soap, and high pressure water. Fill the tank with hot water and soap, agitate it, drain it, and rinse it. Is this practical or am I creating more problems for myself?

Soap & water will have little effect on oil based sludge (even hot water). Dump in a gallon of diesel (#2 oil) or kerosene, slosh around a bit, dump and repeat. for stubborn deposits it wouldn't hurt to leave the diesel in there overnight before you slosh & dump.
 
  • Like
Reactions: Fifelaker
OK, very good, thanks for the advice. I'll try the diesel and see how it goes.

Bob
 
Throw something in there to knock chit loose. I just cleaned and flushed the diesel tank on my lawn mower this past spring. I threw a bunch of spent but clean 9 mm cases in the tank and sloshed it around. What a difference.
 
The rust will be at bottom where water settles and at sides and top above the oil surface

Can you get a pressure washer wand in there?

Sheet metal or drywall screws work well. Hard steel with sharp edges and points
I use for rust remival in mc gas tanks
For hydr tank count the screws and make sure they all come out.
 
  • Like
Reactions: triptester
I put in 2 gallons of kerosene and let it soak most of the day. I drove around the fields this evening and that really bounced the frame and tank around. I have a lot of 9mm casings I can put in. I will do that tomorrow and see how it works.

Thanks again for the good ideas.

Bob
 
Thanks for the advice. I went ahead and used the kerosene only. Looking at the fittings I figured that it would be almost impossible to extract either shell casings or nuts and bolts, once they got in there. I only have 3/4 inch ports on the reservoir and none of them are in line or in corners. I let the kerosene soak the grime for 3 days and bounced it around one more time, and drained it. Not as much crap came out as I had expected, so I decided to power wash it. That helped to free up a lot more but because of the angles I couldn't reach every section of it. While the tank was empty and clean I welded a new axle onto it. I warmed the tank to help evaporate the moisture and prevent more rust. I will change the oil filter after the first few hours to remove any additional loose particles that get picked up by the hydraulic oil.

Bob
 
Status
Not open for further replies.