Best brush for an oval metal liner ?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

CarpenterAnt

New Member
Jul 26, 2014
22
Maine
What's the best brush for an 6" x 10" stainless steel insulated chimney flue liner?

A friend lent me his square metal brush and though I was concerned about scratching the liner I used it anyway. I could tell it was not reaching the inner bends in the oval. I saw a chimney sweep with what looked like a giant feather duster on flexible rods turned by a drill. But I can't find anything like that on the chimney supply websites only the plastic whips, weed wacker style.
 
I use a Rutland sweepsall poly brush either the PFT-8 or PFT-12 with a TLC connector.
 
I ordered the Sooteater by Gardus rather than the Sweepsall by Rutland: reason? The Sooteater attaches to a drill and spins on flexible rods, downside is you need an allen wrench to disconnect the head and the rods. the Sweepsall rods are button lock/unlock but they don't bend and they don't attach to a drill so they don't spin. They can only be used to clean in one direction which means (in my and most cases) from the chimney top down. With the Sweepsall, I can clean the liner from behind the stove and never have to fall off a ladder (or the roof) in the ice and snow - probably the number one excuse for not cleaning.

After seven years of fall and spring burning - never over wintered here - I cleaned the liner which was new in 2007 for the first time this week with a friend's metal bristle chimney brush. The liner looked clean but the clean-out was full to over flowing and the clean-out is two feet deep - that's a lot of creosote. My liner is stainless steel, double if not triple walled and wrapped in an insulation blanket - must be working. My wood has been decent, dry and hard but my fires are frequently smoldering.

I'm afraid I may have scratched the liner when I cleaned it with the metal brush and that this may reduce the creosote repelling properties of the liner's interior finish or cause rusting. I didn't know then about the poly brushes for stainless liners.

My stove is a Vermont Castings 1977 Vigilant. Speaking of which, does anyone know how to access the back of this stove for cleaning? Someone told me the fifty-five inches of secondary-burn flame path which consists of two offset plates one above the other is accessible - if you know how.

Thanks for your suggestions. The Gardus Sooteater cost $48.95 at DIYControls.com. That was the best price I could find. I went ahead and bought additional extension rods, a replacement head and a dryer vent cleaning kit for the benefit of free shipping after $100.00. Otherwise It was $28 for UPS ground shipping. My total bill, $101.23.
 
Last edited:
Good choice. My old Defiant had a similar setup as your Vigilant, I believe. To clean behind the fire back I removed the top oval plate (which I'm not sure your Vigilant has?) and then used a smaller sized tube held onto my shop vac. You could also do the same thing through the pipe outlet.
 
Good choice. My old Defiant had a similar setup as your Vigilant, I believe. To clean behind the fire back I removed the top oval plate (which I'm not sure your Vigilant has?) and then used a smaller sized tube held onto my shop vac. You could also do the same thing through the pipe outlet.

Yes, that would work. I don't have a smaller tube though, just my two inch shop-vac and a 1-1/2" Hoover upright. I could try the dryer vent cleaner in there when it arrives.
 
Yes, that would work. I don't have a smaller tube though, just my two inch shop-vac and a 1-1/2" Hoover upright. I could try the dryer vent cleaner in there when it arrives.

I just use the clear plastic/rubber hose that you can pick up at a hardware store.
 
A large round or rectangular poly brush can be trimmed easily. I also like soot eaters, but i feel a brush does the job just a tad better. I actually use both. A brush at the beginning of the season, then use the soot eater mid winter as touch up when there's snow on the roof.
 
Status
Not open for further replies.