DV Gas Insert Installation... is it okay to cut off the intake vent & not take it to the top?

I would say yes it should be find it is a common thing to do how tall is the chimney?

It's likely ok. It's probably more of a brand specific question. Some brands actually recommend this method of termination. Another important factor is how and if the blockoff plate was installed.

As Shane says....it may be brand specific.

IMHO, it is NOT the normal way of doing things unless specifically covered in the owners manual. Take a look-see.

I know Mendota is one brand that suggested that type of installation in the manual.

If it is listed in the manual, then it is usually fully approved and safe.

We did not usually do them this way since it was really not any easier....we had to drop one pipe down, so why not two.......?

Strangely enough, it might even be a better way to do things in some cases, because there is less impediment to the incoming air.

We used to just install the stubby liner for the fresh air but actually ran into air problems with the FB-IN and FB-Grand units so now we run both liners to the top on every install and we have had much better results. We had to go back and fix a dozen or more installs where the stubby liner was causing probs. I have also seen some fireplaces get a lot of white power all over in them from the stubby install, because they are sucking up particles from inside the old chimney and burning them.

jtp10181 said:

We used to just install the stubby liner for the fresh air but actually ran into air problems with the FB-IN and FB-Grand units so now we run both liners to the top on every install and we have had much better results. We had to go back and fix a dozen or more installs where the stubby liner was causing probs. I have also seen some fireplaces get a lot of white power all over in them from the stubby install, because they are sucking up particles from inside the old chimney and burning them.

Click to expand...

Hi JTP,
Can you tell me what type of problems you ran into by installing the stubby,(3-4 foot section of aluminum intake liner), on the FB Grand model Inserts?
On my FB Grand Insert, the installers ran a three foot section of aluminum liner up the flue for the intake and ran the full lenght aluminum exhaust to the high wind termination cap. They than packed insulation where the pipes go through the damper opening and left the damper inplace but obviously in the open position. The termination cap flange was siliconed to the top of the chimney flue.
I believe,(not totaly sure), that in the owners manual it illustrates both methods.
I would think that the two pipes all the way to the top of the temination cap would be the way to go.

Thanks,
John

DAKSY said:

Webmaster said:

If it is listed in the manual, then it is usually fully approved and safe.

We did not usually do them this way since it was really not any easier....we had to drop one pipe down, so why not two.......?

Strangely enough, it might even be a better way to do things in some cases, because there is less impediment to the incoming air.

Click to expand...

It may work, but it can lead to a colder install..We ALWAYS install the 3" aluminum liner kits with BOTH intake & exhaust running the full length of the chimney - UNLESS it's a HnG FB-Grand or Fb-IN with the 3' SS liner section on the exhaust. We ALWAYS insulate the top & bottom of the chimney. This isn't possible if you "short-stroke" the intake...

Click to expand...

Hi,
Can you tell me what you mean by"Unless its the HnG FB-Grand with the 3' stainless Steel liner section on the exhaust".
How do you like your Jotul Firelight II 600 DV Stove?

Thanks,
John

DAKSY said:

Hi, John,

Can you tell me what you mean by"Unless its the HnG FB-Grand with the 3' stainless Steel liner section on the exhaust".

The HnG FB series inserts generate so much heat coming immediately off the top the aluminum liners wouldn't last very long...They use about a 3' section of 3" SS off the top of the exhaust, which gets connected to the 3" Al liner...

How do you like your Jotul Firelight II 600 DV Stove?

Works the nuts. I've got it installed in one bay of a two-car garage & it totally heats that bay & the studio apartment above it. The GF's daughter & her cats occupy the studio.
I had an old Russo wood-burner in there, but I couldn't be sure that she'd stoke it enough on cold NY winter days to keep the pipes from freezin...So we sucked it up & put the LP Firelight up there on a Skytech 3301 Remote t-stat...
She pays for the fuel, so I'm not gonna kick...

Click to expand...

HI DAKSY,
I just want to get this straight in my head. Your saying that the HnG FB series use a 3' piece of SS pipe connected to the termination cap on top of the chimney, or the top of the insert itself where the slide out tray is located for ease of connecting the intake & exhaust 3"pipes, and than after the 3' SS pipe it is connected the rest of the way down or up the flue of the chimney to the top of the insert via aluminum 3" pipe?
I do know one thing for sure, the FB Grand Insert does throw out some serious heat dispite the numerous problems that have plagued my FB Grand Unit.
I am really glad to hear of the positive comments on your Jotul Firelight 600 Stove.
When I first had mine installed in my rec room, I wasn't to happy with the way it heated the room for a 40K Btu unit, but after reading the owners manual and adjusting the exhaust restrictor to match my chimney height, it really throws out some heat.
Also, at the top of my rec room steps, I keep the door closed and WOW what a difference. The rec room holds the heat much longer and doesn't lose it to the chimney effect by leaving the door open to the living room upstairs. This also keeps the living room floors much warmer preventing drafts, and lets the FB Grand Insert heat my upstairs living area with 18'vaulted ceilings more efficently, I believe.
Thanks for the info!!
John

The FB units come with a 3' SS liner that is connected to the bottom of the 3" alum before you drop it down the chimney. This gets connected to the exhaust of the unit. The exhaust coming out of the unit is so hot the Alum might get trashed so they start off with some SS.

The probs we had was the unit turning off by itself, normally after a few hours of use. The pilot would curl and slowly loose millivolts, being an airflow problem the only thing I could think of was to drop two liners down. We did that and it fixed a couple so we ran with it. Have not had the same kinds of problems since.

jtp10181 said:

The FB units come with a 3' SS liner that is connected to the bottom of the 3" alum before you drop it down the chimney. This gets connected to the exhaust of the unit. The exhaust coming out of the unit is so hot the Alum might get trashed so they start off with some SS.

The probs we had was the unit turning off by itself, normally after a few hours of use. The pilot would curl and slowly loose millivolts, being an airflow problem the only thing I could think of was to drop two liners down. We did that and it fixed a couple so we ran with it. Have not had the same kinds of problems since.

Click to expand...

JTP,
Thanks for the info. I did not know that the liner had this piece of 3' SS. I just thought both the exhaust and the intake liners where made from aluminum.
I never thought that the thought the exhaust of the FB Grand Inserts got quite this hot.
This info. is very helpful especially when you are the owner of one of these particular inserts.

Thanks Again,
John

we use to sell the old arrow dv insert(one of the first dv inserts to come to market)the original instructions showed two liners from the unit to the top cap, what would happen is the exaust gases would sometimes roll beneath the burner and exaust out the intake and the exaust would become the air intake.the solution was to shorten up the intake like you describe promlem solved