1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 4
  1. sedanman
    Post

    There's too much snow!

    Good excuse to get a snowmobile and "groom" your trail.
    Post by: sedanman, Dec 14, 2009 in forum: The Perfect Picture
  2. sedanman
    Post

    Dolmar conversion

    Exactly correct.
    Post by: sedanman, Nov 23, 2009 in forum: The Gear
  3. sedanman
    Post

    Bought a new toy yesterday. Let it snow!

    Whatcha doin' with the old one?
    Post by: sedanman, Nov 23, 2009 in forum: DIY and General non-hearth advice
  4. sedanman
    Post

    Fuel, spark, air . . . and no wasps

    Even when you've seen it before, it can still stump you. I have been tricked by this a few times myself.
    Post by: sedanman, Nov 18, 2009 in forum: The Gear
  5. sedanman
    Post

    Fuel, spark, air . . . and no wasps

    It happens here too. If air can't get out, it can't get in.
    Post by: sedanman, Nov 18, 2009 in forum: The Gear
  6. sedanman
    Post

    Another "curving cut" question

    It may not be a matter of one set of teeth being "sharper" than the other, rather one set may be more aggresive than the other. My suggestion is to...
    Post by: sedanman, Nov 13, 2009 in forum: The Gear
  7. sedanman
    Post

    Second saw?

    Get a spare bar and chain for the saw you have now. If the saw gets pinched, take the power head off the stuck bar and use the spare to cut the saw...
    Post by: sedanman, Nov 8, 2009 in forum: The Gear
  8. sedanman
    Post

    stihl S10

    I would not pay that much for such an old oddball saw. Parts have got to be hard to find at this point. Sure it may run fine now but how long will...
    Post by: sedanman, Nov 5, 2009 in forum: The Gear
  9. sedanman
    Post

    troy-bilt 27ton honda gcv160 splitter

    I have one of these on every 4 cycle engine I own. All my equipment and all of my vehicles NEVER HAD A LEAK. http://www.fumotousa.com/nseries.htm
    Post by: sedanman, Nov 5, 2009 in forum: The Gear
  10. sedanman
    Post

    50Fuel-Pre-Mixed Fuel?

    I have used it. I bought a can to have around for when I ran out of my own mix. Came in mighty handy. Too pricey for full time use but not bad to...
    Post by: sedanman, Oct 29, 2009 in forum: The Gear
  11. sedanman
    Post

    Regreasing Trailer Bearings

    Tighten the nut to about 15 foot pounds, spin the hub over then back the nut off and re-snug it to about 15 INCH pounds, works every time.
    Post by: sedanman, Oct 29, 2009 in forum: DIY and General non-hearth advice
  12. sedanman
    Post

    New Stihl

    362 is the replacement for the 361. 362 is the first of a new generation of Stihl saws. More fuel efficient with lower emissions, the wave of things...
    Post by: sedanman, Oct 29, 2009 in forum: The Gear
  13. sedanman
    Post

    25:1?

    Ok it gets hairy from here on out. If you have your saw adjusted for a perfect air fuel mixture with a fuel oil ratio of 25:1 and then switch to a...
    Post by: sedanman, Oct 29, 2009 in forum: The Gear
  14. sedanman
    Post

    Chain and Bar

    If your local saw dealer is good, he will have a bar rail grinder. "Dressing" the rails from time to time will extend the life of the bar as will...
    Post by: sedanman, Oct 27, 2009 in forum: The Gear
  15. sedanman
    Post

    Made some logging tongs

    I do more of the cut and weld type fabrication myself. Very nice job on the tongs.
    Post by: sedanman, Oct 27, 2009 in forum: The Gear
  16. sedanman
    Post

    25:1?

    Lean siezure of a 2 cycle engine is due to a lean air fuel mixture which runs extremely hot. The high operating tempuratures are the root cause of...
    Post by: sedanman, Oct 26, 2009 in forum: The Gear
  17. sedanman
    Post

    25:1?

    It was once a common mix ratio. The difference between then and now is not the engines but the oils. Oils have gotten much better in modern times and...
    Post by: sedanman, Oct 26, 2009 in forum: The Gear
  18. sedanman
    Post

    help! Dropped my Husky in th creek.

    His 2 cycle chainsaw does not have valves. I'd drain the fuel and oil tanks, flush both out with mixed fuel. Take the plug out and crank the saw...
    Post by: sedanman, Mar 9, 2008 in forum: The Gear
  19. sedanman
    Post

    "Jetting" a saw by spark plug color

    Adjust the low side first, this may not be the final adjustment, you'll re-check after the high side is set. You are looking for a smooth idle with...
    Post by: sedanman, Feb 26, 2008 in forum: The Gear
  20. sedanman
    Post

    Electrical question about 3-wire and 4-wire receptacles

    My understanding is that you NEED a transfer switch to do this properly. You are not completely disconnecting your house from the drop by pulling the...
    Post by: sedanman, Feb 17, 2008 in forum: DIY and General non-hearth advice
Showing results 1 to 20 of 73 Next >
Search Again
Page 1 of 4