1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 4
  1. Rick5472
    Post

    What kind of gloves are these?

    Thanks! That's great Ejectr! I need a better monitor or eyes!
    Post by: Rick5472, Nov 26, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. Rick5472
    Post

    What kind of gloves are these?

    Thanks...they seem to be more of a knit cotton type of glove without any cuff. They are cut short to the wrist. At 3:27 into the video you can get...
    Post by: Rick5472, Nov 26, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. Rick5472
    Post

    What kind of gloves are these?

    I am not looking for the welding gloves Danny. I am looking for the white cotton looking gloves that show up at 1:18 and 3:27 into the video....
    Post by: Rick5472, Nov 26, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. Rick5472
    Post

    What kind of gloves are these?

    That's what I thought but have not been able to find them anywhere. I have seen guys wear these type of gloves doing natural gas line work before...
    Post by: Rick5472, Nov 26, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. Rick5472
    Thread

    What kind of gloves are these?

    I have been trying to find a particular type/brand of gloves that have been used to clean pellet stoves in a Harman demo video but have been unable...
    Thread by: Rick5472, Nov 26, 2012, 15 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. Rick5472
    Post

    Pellet Storage

    Watch out for the cat though...==c
    Post by: Rick5472, Nov 16, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. Rick5472
    Post

    Review of Home Depot's Pellets (Maryland 2012)

    I got my 2 tons of O'Malley's from Wood Floors Plus delivered to Columbia, MD for $35 a ton. Wished I had a bigger truck...:)
    Post by: Rick5472, Nov 16, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. Rick5472
    Post

    Harman Advance "Status Light"

    The room temp was dropping so it is supposed to keep the temp within 1-2 degrees. It should have cranked up the heat but it went out.
    Post by: Rick5472, Nov 15, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. Rick5472
    Post

    Harman Advance "Status Light"

    Once again last night, the stove went out in room temp, auto igniter mode. The status light was out and the power light was on. That was it. I...
    Post by: Rick5472, Nov 15, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. Rick5472
    Post

    Harman Advance "Status Light"

    Mine seems just to remain off ...lately..and the unit shuts down completely.
    Post by: Rick5472, Nov 14, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. Rick5472
    Post

    Harman Advance "Status Light"

    Lineman...I guess mine is working that way too...I just never noticed after all these years. I assume after the temperature drops again that the...
    Post by: Rick5472, Nov 14, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. Rick5472
    Post

    Harman Advance "Status Light"

    I am still wondering about the status light on the Advance. Since I haven't watched the lights cycle for more than a few minutes I thought I would...
    Post by: Rick5472, Nov 14, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. Rick5472
    Post

    Harman Advance "Status Light"

    Scott...Thanks for the info. The knob didn't seem to be loose to me but I will check it out tonight the see if that could be the problem. I am...
    Post by: Rick5472, Nov 13, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. Rick5472
    Thread

    Harman Advance "Status Light"

    My Advance turned off during the middle of the night yesterday and I thought it was unusual since the temperature was over 5 degrees below what the...
    Thread by: Rick5472, Nov 13, 2012, 11 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. Rick5472
    Post

    Igniter for harman accentra insert

    I used a pair of needle nosed pliers to get the tabs twisted so I could get the plate off from the igniter I replaced on my Advance. Be sure to...
    Post by: Rick5472, Oct 4, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. Rick5472
    Post

    Harman Advance Igniter

    I could be over thinking this.......:)
    Post by: Rick5472, Sep 28, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. Rick5472
    Post

    Harman Advance Igniter

    I am wondering now if it would hurt to pull the wires out through the grommet most of the way until I feel a little resistance (since the igniter is...
    Post by: Rick5472, Sep 28, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. Rick5472
    Post

    Harman Advance Ignitor Replacement

    Finally got the igniter back in the stove. Getting ready to put the cable ties on the wires I had to remove to get the igniter wires out of the...
    Post by: Rick5472, Sep 25, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. Rick5472
    Post

    Harman Advance Igniter

    Finally got the igniter back in the stove. Getting ready to put the cable ties on the wires I had to remove to get the igniter wires out of the burn...
    Post by: Rick5472, Sep 25, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. Rick5472
    Post

    Harman Advance Igniter

    I see what you mean. The slots in the plate are off center as you can see in the attached photo. I will be sure to mark it accordingly so that...
    Post by: Rick5472, Sep 13, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 71 Next >
Search Again
Page 1 of 4