1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. bdcbean
    Post

    **UPDATE** Pellets not sliding well in hopper - My fix w/pics

    It's a trade off you get, but there is little point in a large capacity hopper if you have to move the pellets by hand once it gets half full. I was...
    Post by: bdcbean, Oct 17, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. bdcbean
    Post

    production and quality of stoves

    It comes down to the quality control a manufacturer has in place. It's quite easy for a guy on a welder to be having a bad day and miss a spot but...
    Post by: bdcbean, Oct 16, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. bdcbean
    Post

    Big E and 1/2 bag per day pellets

    Same pellets over several tests. The average size etc is all very similar. There are a lot of variables though this is one regardless.
    Post by: bdcbean, Sep 17, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. bdcbean
    Post

    Big E and 1/2 bag per day pellets

    Here is an odd one for you. Why would a feed rate measured manually by catching the pellets as they fall out of the auger and weighing it come up...
    Post by: bdcbean, Sep 16, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. bdcbean
    Post

    Bio Furnace demo unit install *****08-28-08 5:00 PM new pics posted*****

    And what makes the self clean so special? :)
    Post by: bdcbean, Aug 29, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. bdcbean
    Post

    I don't think my P38 is burning properly

    I don't think dampers in pellets stoves are allowed.....forced combustion from the front end could result in smoke spillage. Most dampering is on...
    Post by: bdcbean, Aug 29, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. bdcbean
    Post

    Wide band O2 sensor for control of combustion.

    I would imagine the soot would not be good for it.. as well as the corrosive leftovers. They don't last long with lead fuel in cars even. As RND...
    Post by: bdcbean, Aug 29, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. bdcbean
    Post

    Wide band O2 sensor for control of combustion.

    Any luck with this? I don't think Austoflamme use an 02 sensor at all, I believe they just have a exhaust temp sensor which gives them a larger...
    Post by: bdcbean, Aug 28, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. bdcbean
    Post

    Lucky Day I fought and I won.

    Mechanics are known world wide for upping the price.. I also do all my own work. I simply do not trust people I don't know to work on anything I own..
    Post by: bdcbean, Aug 15, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. bdcbean
    Post

    Installer Said Outside Air Kit Not Necessary?????

    Run nitrogen or helium in your tires :) (thats why race cars do not use air) As for the fuel temps, I recently installed a control system for my...
    Post by: bdcbean, Aug 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. bdcbean
    Post

    Ceiling fans and winter

    My guess would be that because the hot air is rising, the fan will pull this hot air up and as it has no where to go it will then hit the roof and be...
    Post by: bdcbean, Aug 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. bdcbean
    Post

    thermostat installation

    My guess would be that it reverts to different stages in the programme for a set input. So it would have to change the fan and auger together or you...
    Post by: bdcbean, Aug 6, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. bdcbean
    Post

    Installer Said Outside Air Kit Not Necessary?????

    In an automobile combustion engine you are using compression to make the power. Compression = heat. If you can lower the temp before this process...
    Post by: bdcbean, Aug 6, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. bdcbean
    Post

    MT Venon AE Flame Height

    edit: Old thread. sorry posted by mistake..
    Post by: bdcbean, Jul 27, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. bdcbean
    Post

    New England Distributors

    Cheers. Sent you an email.
    Post by: bdcbean, Jul 24, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. bdcbean
    Post

    New England Distributors

    Hey anything is possible.
    Post by: bdcbean, Jul 24, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. bdcbean
    Thread

    New England Distributors

    Hi guys, I am aware that there is quite a few shops/installers in New England on these forums and I wanted to inquire about someone retailing our...
    Thread by: bdcbean, Jul 24, 2008, 4 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. bdcbean
    Post

    RE: Looks like the oil dealers in Maine don't like the fact that pellet stoves are pretty popular

    Got ya. Thats a few cars. Gas down here in NZ is very expensive now. I have a very modded turbo car and it costs me a fortune every time I even...
    Post by: bdcbean, Jul 23, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. bdcbean
    Post

    RE: Looks like the oil dealers in Maine don't like the fact that pellet stoves are pretty popular

    I was looking at the possibility for more feedback loops with our pellet fire. Wideband 02 sort of setup to completely control the burn rate. The...
    Post by: bdcbean, Jul 23, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. bdcbean
    Post

    Hi

    Tha augers are quite slow rpm high torque and can easily crush up any pellets that get in the way. Fines are a problem especially when people do not...
    Post by: bdcbean, Jul 14, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2