1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. Peltz
    Post

    Auger not working - Enviro EF3

    It has been pretty warm the last couple of days here in Maryland so I have not been burning the stove, but I have a good feeling that all the...
    Post by: Peltz, Dec 11, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. Peltz
    Post

    Auger not working - Enviro EF3

    I think I found success. I hooked all the new parts together and it worked. Previously l hooked one part at a time trying a process of elimination...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. Peltz
    Post

    Auger not working - Enviro EF3

    Did as you said. Had a nice flame in the burn area. The multimeter never flipped from 0.L to 0.000 on the vacuum switch. The convection blower is a...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. Peltz
    Post

    Auger not working - Enviro EF3

    Tested the 140° F sensor as described. At first it read 0.L then when removed and it next to a candle the meter read 0.000 ohms.
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. Peltz
    Post

    Auger not working - Enviro EF3

    Just climbed out on the roof and the flue cover is wide open. No obstructions
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. Peltz
    Post

    Auger not working - Enviro EF3

    Yes. Top port. The original switch is currently installed.
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. Peltz
    Post

    Auger not working - Enviro EF3

    I purchased a new vacuum sensor and it is different than the original. I suppose it is a replacement model. Anyway, when I attached it nothing...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. Peltz
    Post

    Auger not working - Enviro EF3

    Stuck a needle through it. Not obstructed.
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. Peltz
    Post

    Auger not working - Enviro EF3

    If you mean the vacuum hose, there is a red hose that connects a barb on the vacuum switch to a barb on the stove in the "exhaust chamber" (my...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. Peltz
    Post

    Auger not working - Enviro EF3

    According to the owner's manual it is a vacuum switch.
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. Peltz
    Post

    Auger not working - Enviro EF3

    The flue cap is not clogged. It is not really a wire mesh, you can fit a pencil or maybe your pinky through it, but it is too small for a bird or...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. Peltz
    Post

    Auger not working - Enviro EF3

    Probes not touching reads 0.L, probes touching reads 0.000
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. Peltz
    Post

    Auger not working - Enviro EF3

    I did not feel too bad about venting the stove into the room since it is totally clean. Not even a hint of soot came out of the exhaust. I have...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. Peltz
    Post

    Auger not working - Enviro EF3

    When I am performing all of these tests the stove is disconnected from the flue line, in other words the combustion/blower is blowing into the room,...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. Peltz
    Post

    Auger not working - Enviro EF3

    One other thing that may be interesting, or not, is that the pellets in the burn pot will ignite if I leave the stove on for a couple of minutes.
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. Peltz
    Post

    Auger not working - Enviro EF3

    When the new vacuum switch did not fix the problem I hooked up the original Honeywell switch. At least I can return the new one and get a refund. I...
    Post by: Peltz, Dec 9, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. Peltz
    Post

    Auger not working - Enviro EF3

    I attached the pins of the multimeter to the leads that connect to the exhaust blower it read 122.9 volts. Yes, there are two blowers, one that...
    Post by: Peltz, Dec 8, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. Peltz
    Post

    Auger not working - Enviro EF3

    Also, the auger does not turn at all if the vacuum switch is not jumped.
    Post by: Peltz, Dec 8, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. Peltz
    Post

    Auger not working - Enviro EF3

    The combustion blower is on separate control and must turned on separately from the control that determines auger speed/burn rate. The exhaust blower...
    Post by: Peltz, Dec 8, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. Peltz
    Post

    Auger not working - Enviro EF3

    I attached direct power the auger motor in it rotated freely with pellets in the hopper. I attached the pins on multimeter to slots on the wire leads...
    Post by: Peltz, Dec 8, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2