1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 3
  1. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    Wil, The Voltage measured at the connector on the control board (the wires that feed the igniter) was 118 volts AC and the igniter resistance was 47...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    Hailfire, I started the season with 3 new bags of pellets the local pellet dealer gave me to try out. They didn't work either so I tried my left...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    Wil, The igniter was warranty. However, I'm beginning to wonder if it's the right one. My daughter picked it up from the dealer on her way thru...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    Hey Wil, No, the stove doesn't continually feed pellets until the burn pot overflows. It will feed for a minute then stop for about 3 minutes (I've...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    The igniter is mounted in contact with the underside of the burn pot floor and the pellets are sitting on the burn pot floor right above it. They...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    I waited a good 5 minutes and no there was no smoke. The furnace waits 2 or 3 minutes to detect heat then goes into a feed cycle where it feeds...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    You are absolutely right, Hailfire. An obstruction in the air intake does increase vacuum in the combustion chamber. I placed my hand over the air...
    Post by: ex-oil slave, Oct 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. ex-oil slave
    Post

    A question about draft readings on a Harman PF100 furnace

    Thanks Hailfire, The area under the igniter is clean and the igniter is new. Still no fire unless I manually light it.
    Post by: ex-oil slave, Sep 27, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. ex-oil slave
    Thread

    A question about draft readings on a Harman PF100 furnace

    When I installed this furnace (new) the manual suggested using a manometer to check the draft readings at the firebox at both high and low speed...
    Thread by: ex-oil slave, Sep 27, 2010, 22 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    The igniter is new and has never actually started a fire going since I installed it last week for the first time. It does get hot (red hot) when...
    Post by: ex-oil slave, Sep 17, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    Yes, the igniter was warming up t that time.
    Post by: ex-oil slave, Sep 17, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    I'll check that tonight. I think I already set the dip switches as you indicate. Someone suggested that fix under a thread about 6 blink codes a...
    Post by: ex-oil slave, Sep 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    I tried two different batches of pellets. One new (sealed bags) this year and one from the tail end of last years order (again, sealed bags). I'm...
    Post by: ex-oil slave, Sep 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    I did remove the igniter from the cradle and I thought of that last night (the cover plate part of your quote) so I reversed the cover plate and...
    Post by: ex-oil slave, Sep 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    No air pump. Combustion motor pulls ait in under the burnpot and up thru the holes in the floor of the burnpot.
    Post by: ex-oil slave, Sep 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. ex-oil slave
    Post

    Igniter gets hot but pellets won't light on a Harman PF100

    There does seem to be good airflow thru the burnpot (enough to cause the pellets to hop around when I manually light the stove and it's burning...
    Post by: ex-oil slave, Sep 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. ex-oil slave
    Thread

    Igniter gets hot but pellets won't light on a Harman PF100

    The igniter I have seems to be OK. Resistance is 49 ohms, 13 fins, gets hot to the touch when installed under the burnpot, but won’t ignite the...
    Thread by: ex-oil slave, Sep 16, 2010, 23 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. ex-oil slave
    Thread

    PF100 Igniter failures

    How many PF100 or PB105 owners have had igniter failures? For the PB105 owners this does not include the pressure igniter system. I’m talking about...
    Thread by: ex-oil slave, Apr 19, 2010, 6 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. ex-oil slave
    Thread

    PF100 Igniter failures

    How many PF100 or PB105 owners have had igniter failures? For the PB105 owners this does not include the pressure igniter system. I'm talking about...
    Thread by: ex-oil slave, Apr 19, 2010, 2 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
  20. ex-oil slave
    Post

    UPDATE PB105 Pressure Ignition System Installed

    stoveguy..... I can't talk about the burnpot in the picture as it isn't mine, but in my case, I kept the holes clean and clear and it made no...
    Post by: ex-oil slave, Mar 3, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 45 Next >
Search Again
Page 1 of 3