1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. Murph
    Post

    Auger will not work

    Make sure the auger is not jammed as well when you power the motor.
    Post by: Murph, Apr 23, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. Murph
    Post

    Pellet pro II

    Thanks Don for answering the question. I am going back to the house and remember seeing the wing nut on the face plate of the fine box but I was...
    Post by: Murph, Apr 20, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. Murph
    Thread

    Pellet pro II

    Want to know how to take apart the auger fine box with the adjuster rod that comes through the box cover and then through the face plate of the...
    Thread by: Murph, Apr 19, 2013, 3 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. Murph
    Post

    Empress FS not lighting all the time

    Any errors? Is the burn pot even getting warm? Loose wire? Has the system ( stove and venting) been thoroughly cleaned?
    Post by: Murph, Apr 18, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. Murph
    Post

    Quadra Fire 1000 little problem..

    Looking at the manual for the 1000 looks like it is on the back wall on the right side facing the stove and is called a vacuum switch. Jumping this...
    Post by: Murph, Apr 12, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. Murph
    Post

    Quadra Fire 1000 little problem..

    Have you jumped the pressure switch?
    Post by: Murph, Apr 11, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. Murph
    Post

    Harman XXV makes clunk/bang when feeding

    Had to replace the auger motor on a Accentra FS due to it being ripped apart. Then had a similar call only loud noise was the issue again found the...
    Post by: Murph, Mar 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. Murph
    Post

    NFI Certification

    Test
    Post by: Murph, Feb 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. Murph
    Thread

    NFI Certification

    Just took the test today and passed, very excited but still a lot to learn. Next will be my installers license but that will take awhile and more...
    Thread by: Murph, Feb 23, 2013, 11 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. Murph
    Post

    Could I benefit from a 4" exhaust?

    Clinkers are to my understanding caused by silica(sand) in the pellets and happens when the ash fuses with the silica. Bad pellets. Your pipe for...
    Post by: Murph, Jan 29, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. Murph
    Post

    Harman service?

    All labor and parts are covered at my shop if there is a defect at fault. Harman only pays us so much towards the labor and we cover the rest, the...
    Post by: Murph, Jan 29, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. Murph
    Post

    Mcfeeders

    I guess that's possible although I checked them and they did not seem swollen or overly soft although they certainly did not have the hardness of...
    Post by: Murph, Jan 29, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. Murph
    Thread

    NFI Rcomendations

    According to a section on venting it is suggested that in cold climates the vent pipe should be kept in the envelope of the home to insure maximum...
    Thread by: Murph, Jan 29, 2013, 8 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. Murph
    Post

    Harman service?

    I am a tech so I cannot speak to homeowner support but most of your support should come from the dealer and the people that do the service calls. I...
    Post by: Murph, Jan 29, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. Murph
    Thread

    Mcfeeders

    Cleaned Englander last night then tried to light it only the pellets would not light. Tried for fifteen minutes no luck. Had some Oakanagans in truck...
    Thread by: Murph, Jan 29, 2013, 5 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. Murph
    Post

    PS40 shutting down

    I thought that might be the case with regards to failing while operating. With regards to vacuum issues are you saying that the feed can be lessened...
    Post by: Murph, Jan 28, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. Murph
    Thread

    PS40 shutting down

    Went and cleaned a PS40 that was shutting down some times a half hour maybe more but seemed to run fine if it made it past an hour or more. Thought...
    Thread by: Murph, Jan 28, 2013, 4 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. Murph
    Post

    Harman auto shut down on UPS

    As long as you have an E series board the board can use the backup power for a shut down only by pulsing the combustion motor for the complete shut...
    Post by: Murph, Jan 20, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. Murph
    Thread

    Accentra Keeps Shutting Down

    I go to a customers house for a stove that keeps shutting down and eventually find that the pressure switch is bad and replace it, still the stove...
    Thread by: Murph, Jan 11, 2013, 3 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. Murph
    Post

    Burnpot Filling Up

    What Eric was talking about with regards to behind the clean out panels was open areas on the back side of the burn box wall and suggested Pounding...
    Post by: Murph, Jan 8, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 36 Next >
Search Again
Page 1 of 2