1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 4
  1. Mr Fixit
    Post

    drolet eco 45 auger question

    Yes- the other 157 people who read this thread were at least smart enough to ignore my mistake in reading the post and graciously move on. Thanks for...
    Post by: Mr Fixit, Jan 14, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. Mr Fixit
    Post

    Enviro Max Trouble

    Double check that the auger motor isn't turning- the set screw may have just come loose and the auger is spinning freely on the motor shaft. By pass...
    Post by: Mr Fixit, Jan 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. Mr Fixit
    Post

    Pellet stove exhaust

    Maybe a weak exhaust blower?
    Post by: Mr Fixit, Jan 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. Mr Fixit
    Post

    Motor clicking

    Just a thought, maybe worn bushings at the top and/or bottom of the auger are giving excessive play in the auger, allowing pellets to go where no...
    Post by: Mr Fixit, Jan 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. Mr Fixit
    Post

    Majestic flames having troubles on high...

    yes Majestic has gone belly up ( not unlike your gas valve) so parts may be hard to get, if any are needed. Do you use propane (LP) or natural gas...
    Post by: Mr Fixit, Jan 13, 2010 in forum: It's a Gas!
  6. Mr Fixit
    Post

    heat n glo ipi 6000 does not light

    Can you see the spark at the pilot? It may be sparking, but somewhere other than where it is supposed to be.
    Post by: Mr Fixit, Jan 13, 2010 in forum: It's a Gas!
  7. Mr Fixit
    Post

    drolet eco 45 auger question

    Something else I thought of that is common with these stoves- on some of the earlier models of this particular stove, they neglected to properly...
    Post by: Mr Fixit, Jan 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. Mr Fixit
    Post

    Whitfield Profile 20

    sounds like not enough air. Even though you are opening up the damper as wide as it will go, the air intake is driven by the exhaust going out. Give...
    Post by: Mr Fixit, Jan 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. Mr Fixit
    Post

    Profile 30 insert problem

    So other than this buzzing noise, the stove is operating normally?
    Post by: Mr Fixit, Jan 12, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. Mr Fixit
    Post

    Whitfield Quest Insert Pellets Plugging UP

    ya macman is right, definitely an air issue...if all is clean properly, a possible bad exhaust blower? What is the flame like when it is burning?
    Post by: Mr Fixit, Jan 11, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. Mr Fixit
    Post

    drolet eco 45 auger question

    Check the hi temp sensor on the right side of the stove at the front on the inside. It has a little red button on it. Push that button in and try...
    Post by: Mr Fixit, Jan 11, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. Mr Fixit
    Post

    drolet eco 45 auger question

    What is the background on the problem? Is this an intermittant problem? Is the stove making any unusual noises? Is it clean? If I understand you...
    Post by: Mr Fixit, Jan 11, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. Mr Fixit
    Post

    Do I have a bad motor or Control Board?

    Keep in mind that this is how the speed of the blower is regulated by the circuit board, by varying the voltage. It may very well be that it is...
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. Mr Fixit
    Post

    Do auger motors or any other componets need oil or grease?

    Personally, I do not oil anything on a pellet stove. I find the oil just serves to attract and hold dust and debris in area's that should not have...
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. Mr Fixit
    Post

    My ash smells like gas.

    must...not...make...joke... awww what the heck! I guess the beeno in the hopper didn't help?
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. Mr Fixit
    Post

    pellets not sliding to bottom of hopper

    No worries brother. I am looking forward to mythbusters doing that episode, though.
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. Mr Fixit
    Post

    OFFICIAL: Post your leaf blower stove pipe cleaning pics.

    LOL you guys are nuts. With my luck, I would try that and destroy some little old ladie's laundry hanging on the line next door. I think I will stick...
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. Mr Fixit
    Post

    My ash smells like gas.

    Are you drawing combustion air from outside? Perhaps the air intake is sucking fumes in from outside ie your sled or a snowblower?
    Post by: Mr Fixit, Jan 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. Mr Fixit
    Post

    Need Help - No Heat/Flame from Gas Insert

    Your welcome. That will be $89.95 please. ;-P
    Post by: Mr Fixit, Jan 10, 2010 in forum: It's a Gas!
  20. Mr Fixit
    Post

    york insert keeps jamming

    That pellet vac is slick. Thanks for the link, mac.
    Post by: Mr Fixit, Jan 9, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 68 Next >
Search Again
Page 1 of 4