1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 6
  1. cantman
    Post

    Searching for pellet dealers in NJ or Eastern PA

    Ambler Fireplace in Colmar PA has Hamer's pellets for $275/ton
    Post by: cantman, Dec 4, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. cantman
    Post

    Harman P43 Air Flow / Left Side Burn Issues

    egrims- What is your exhaust venting setup? (length,vertical/horizontal,size) I think your strong left side initial startup flame is not a big...
    Post by: cantman, Nov 2, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. cantman
    Post

    Harman Pellet Stove P68 Award Winning 68,000 BTU Bronze & Brass (Grand Rapids) $3000 -NOT MINE, JUST

    I looks like the "white balance" is off from the camera that took the pic. Picture is way too yellow.
    Post by: cantman, Oct 27, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. cantman
    Post

    Harman XXV Distribution Blower

    Mike in PA- You may need to slightly pry the steel flange around the edge of the fan to get it loose. I'll usually take a screwdriver and hammer and...
    Post by: cantman, Sep 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. cantman
    Post

    almost ready to go back to propane, cause this is getting old fast.

    On my XXV with outside air intake, I was over-drafting and sending most of the heat up the stack. My solution was to place foil tape over the intake...
    Post by: cantman, Feb 9, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. cantman
    Post

    Harman XXV crunch sound

    Normal...Normal...Normal
    Post by: cantman, Jan 26, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. cantman
    Post

    Hamer's Hot Ones Users?

    Forya..Where did you buy your pellets from? I also live in "Bucks County" (Lower) and I have a ton of Hamer's waiting to be burned. I bought mine...
    Post by: cantman, Jan 16, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. cantman
    Post

    Harman XXV Distribution Blower

    Does the stove have a “high/low†switch to control the room air (distribution) blower? I have a XXV and my switch is located on the inside of the...
    Post by: cantman, Dec 19, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. cantman
    Post

    Harman Advance - Week Distribution blower speed

    Does the stove have a "high/low" switch to control the room air (distribution) blower? I have the XXV and my switch is located on the inside of the...
    Post by: cantman, Dec 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. cantman
    Post

    Hamers seem to be different this year?

    What date code is on the Hamer pellet bag?
    Post by: cantman, Dec 12, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. cantman
    Post

    P68 Ash Pot problem

    just trying to help Eric[/quote] He really is! Does she not notice this?
    Post by: cantman, Dec 2, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. cantman
    Post

    Lux TX9100E & Enviro M55

    If you touch the two wires together that come from the back of the stove, does the stove start firing? If it does, then your issue is with the...
    Post by: cantman, Nov 7, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. cantman
    Post

    NEW XXV up and running, extremely hot vent ?

    My XXV also gets hot at the exhaust. The exhaust flue setup is exhaust flange to appliance adapter,appliance adapter to 4" cleanout "T", and a...
    Post by: cantman, Nov 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. cantman
    Post

    XXV condensation in hopper?

    Marylu-I have a XXV like you and on occasion have noticed the same presence of moisture on the glass hopper lid. I've attributed mine to a few...
    Post by: cantman, Oct 30, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. cantman
    Post

    starting pellet stove

    My Harman XXV has always needed the door opened for a few minutes to establish a deep enough ember base. If you close the door too quickly, the...
    Post by: cantman, Oct 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. cantman
    Post

    Question for pellet stove owners...

    Either call beforehand, or send out a courtesy post card to confirm the time and date of the customer made appointment. Always have a customer...
    Post by: cantman, Oct 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. cantman
    Post

    At My Wits End

    Why don't you remove the appliance adapter, clean the adapter and the male portion of the exhaust outlet, high temp silicone both male & female...
    Post by: cantman, Oct 24, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. cantman
    Post

    At My Wits End

    What type of venting do you have? How long is the exhaust venting?
    Post by: cantman, Oct 22, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. cantman
    Post

    How to break the silicone attaching stove to pipe?

    I used Rutland's "Direct Vent Stove Sealant" on Pellet Vent Pro. The sealant label says it can be removed but I haven't been able to do that to mine....
    Post by: cantman, Oct 20, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. cantman
    Post

    Down to my last 16 bag's, How many bags do you have?

    I have a little over a ton left. I always purposely buy slightly more than I need so the next season starts with a surplus.
    Post by: cantman, Mar 14, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 107 Next >
Search Again
Page 1 of 6