1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. cdnxj
    Thread

    Security Chimneys Secure Temp ASHT

    I have an older Security Chimneys BIS with a 7" ID factory chimney system. I have been thinking about yanking the BIS out and installing a...
    Thread by: cdnxj, Oct 13, 2011, 1 replies, in forum: The Hearth Room - Wood Stoves and Fireplaces
  2. cdnxj
    Post

    Excessive Vapor/Moisture In DV Gas Stove Pipe

    Totally normal - its just due to the fact that you have an exterior vented cap that is letting in all kinds of cold air (especially when the stove...
    Post by: cdnxj, Jan 27, 2011 in forum: It's a Gas!
  3. cdnxj
    Post

    soot problems

    Not sure about your vent setup but on my VC there is a exhaust pipe restrictor plate. With the plate in the pipe (effectively reducing the...
    Post by: cdnxj, Jan 20, 2011 in forum: It's a Gas!
  4. cdnxj
    Post

    soot problems

    Make sure your air shutters are open all the way (sounds like you have done this...) and check to make sure your logs are in the right position. My...
    Post by: cdnxj, Jan 20, 2011 in forum: It's a Gas!
  5. cdnxj
    Post

    Who owns a Toyota Prius and how do you like it?

    Thought I would chime in here since there has been a bit of discussion on non-Prius hybrid models. I drive a 2006 Toyota Highlander Hybrid, I have a...
    Post by: cdnxj, Jan 13, 2011 in forum: The Green Room
  6. cdnxj
    Post

    stardance 5 year old stove

    I think the Stardance came in both natural vent and direct vent. You would have to get the model number to confirm. I don't think you can modify a...
    Post by: cdnxj, Dec 16, 2010 in forum: It's a Gas!
  7. cdnxj
    Post

    Stove ID

    Oh OK, didn't realize you knew the manufacturer. Lopi is a pretty reputable stove mfg. Probably an older unit if it doesn't look similar to any of...
    Post by: cdnxj, Dec 2, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  8. cdnxj
    Post

    Stove ID

    Could be an older Challenger stove, they are made in Ontario by Reverso. Non-cat, non EPA....
    Post by: cdnxj, Dec 2, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  9. cdnxj
    Post

    VC Radiance 2560 pilot won't remain lit

    I tried a few different pilot shield configurations and seem to have found the solution. Pilot has been going steady for several days without any...
    Post by: cdnxj, Nov 14, 2010 in forum: It's a Gas!
  10. cdnxj
    Post

    VC Radiance 2560 pilot won't remain lit

    From what I can tell the restrictor plate is recommended for vertical terminations. Can anyone confirm if I should ditch the plate for a horizontal...
    Post by: cdnxj, Nov 9, 2010 in forum: It's a Gas!
  11. cdnxj
    Post

    VC Radiance 2560 pilot won't remain lit

    Yes - its a VC listed part and was in the unit when I bought it. I'll have to check the manual to see if there is anything specific about the...
    Post by: cdnxj, Nov 9, 2010 in forum: It's a Gas!
  12. cdnxj
    Post

    VC Radiance 2560 pilot won't remain lit

    Bump on this thread, my question is along the same lines. I have a VC Radiance, LP direct vent, horizontal termination, approx 36" vertical. Bought...
    Post by: cdnxj, Nov 9, 2010 in forum: It's a Gas!
  13. cdnxj
    Post

    Flame height, heat output, soot etc.

    Thanks Dave, So where do I want to run this for max efficiency and heat output? Higher flame or lower flame???
    Post by: cdnxj, Nov 7, 2010 in forum: It's a Gas!
  14. cdnxj
    Post

    Flame height, heat output, soot etc.

    Checked my air shutters, there are 2 - one for front and rear burners. Both were wide open. I may have the logs incorrectly placed. I also put in...
    Post by: cdnxj, Nov 6, 2010 in forum: It's a Gas!
  15. cdnxj
    Thread

    Flame height, heat output, soot etc.

    Just installed a VC Radiance on LP. Bought it used so I have little in the way of dealer support. Wondering how much the flame height control knob...
    Thread by: cdnxj, Nov 6, 2010, 5 replies, in forum: It's a Gas!
  16. cdnxj
    Post

    Old stove

    How about this one: http://legacy.vermontcastings.com/catalog/elements/files/2007/20004409_Radiance_RNVOD.pdf
    Post by: cdnxj, Nov 4, 2010 in forum: It's a Gas!
  17. cdnxj
    Post

    Looking for an NGLP Conversion Kit #5093 for Vermont Castings Radiance 2600 HELP!

    Try this link: http://www.cozycabinstoveandfireplaceparts.com/cgi/display.cgi?item_num=2770-2779 Conversion kit for the Honeywell is listed at...
    Post by: cdnxj, Nov 4, 2010 in forum: It's a Gas!
  18. cdnxj
    Post

    Options for laying pipe

    I just had a propane tank installed, if you just have one gas-fired appliance why not get an upright tank? I had a 420 lb tank installed right next...
    Post by: cdnxj, Nov 4, 2010 in forum: It's a Gas!
  19. cdnxj
    Post

    Vermont Castings Radiance Gas Stove??

    My VC Radiance is hooked up and running great. My propane supplier installed a 420 lb tank with 100 litres of propane to get me started. After a...
    Post by: cdnxj, Nov 4, 2010 in forum: It's a Gas!
  20. cdnxj
    Post

    Selkirk Direct Vent Pipe

    I'm just going by the instructions right in the VC Radiance manual...it clearly says a vinyl siding standoff must be used when installed on vinyl...
    Post by: cdnxj, Oct 8, 2010 in forum: It's a Gas!
Showing results 1 to 20 of 28 Next >
Search Again
Page 1 of 2