1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 4
  1. jimmie ray
    Post

    The 2010-11 Pellet Stove Girl Pin-Up Calender

    Mo Gandhi had better legs than that...
    Post by: jimmie ray, Nov 7, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. jimmie ray
    Post

    The 2010-11 Pellet Stove Girl Pin-Up Calender

    I prefer a girl with an extended hopper, and a nice trim.
    Post by: jimmie ray, Oct 31, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    You don't personally fire-up the unit and wait for a proper shutdown, unless there was an operational complaint, do you? I had a hunch about the...
    Post by: jimmie ray, Sep 15, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    Just accessed the Harman website dealer login section, where their technical bulletins on this are. I'll have to go back to see what control and...
    Post by: jimmie ray, Sep 13, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. jimmie ray
    Post

    P43 optional log set

    That picture in Harman's literature sure seems to show the same logs, placed as you have them. Not very appealing or representative of what a real...
    Post by: jimmie ray, Sep 10, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. jimmie ray
    Post

    Low Draft Setting

    A high draft reading will make ignition take longer, since the ignitor is being cooled excessively by the air velocity. Changing the ignitor may...
    Post by: jimmie ray, Sep 4, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. jimmie ray
    Post

    Low Draft Setting

    A high reading at low fire can cause operational problems, and would obviously affect the efficiency. Did you try lowering the reading, by turning...
    Post by: jimmie ray, Aug 31, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. jimmie ray
    Post

    Embers

    Embers for gas logs are usually pieces of fluffy rockwool or small chunks of lava rock, which will give a realistic glow when placed near the burner...
    Post by: jimmie ray, Aug 27, 2010 in forum: It's a Gas!
  9. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    I am indeed on "cleanup" duty, but let's not dwell on that aspect... The one visit I made revealed wires were very prone to disconnection as the...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    It's funny I read someone here suggested a live chat section - I can't even keep up with this one thread! Yes, the ignitor wires were crimped,...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    The ESP probe sends a resistance reading to the control, which then correlates a temperature to that reading. So I would still have to check the...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    This is a newly installed stove, so I would think the replacement of the ESP probe should not have been necessary. I believe the convection blower...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. jimmie ray
    Post

    Harman diagnostic tool / Accentra problem

    Not very complicated - I guess that's why they figure no instructions are necessary... But would the diagnostic tool indicate an operational...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. jimmie ray
    Post

    Pellet Stove Vent T

    If you can peek inside the venting, you might see globs of sealant at the joints as a sign that it was used. Sealant around the outside is not...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. jimmie ray
    Post

    Pellet Stove Vent T

    Most venting products don't require sealant at the joints, but the installer might be in the habit of applying it to prevent callbacks on leaks. If...
    Post by: jimmie ray, Aug 26, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. jimmie ray
    Thread

    Harman diagnostic tool / Accentra problem

    We just got the diagnostic tool from Harman, which plugs into the control board for troubleshooting. No instructions provided, and I can't find the...
    Thread by: jimmie ray, Aug 26, 2010, 15 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. jimmie ray
    Post

    Harman Issue

    Do you use the diagnostic tool, that plugs into the control board? We just got one, but there were no instructions for using it. Wasted alot of time...
    Post by: jimmie ray, Aug 25, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. jimmie ray
    Post

    Magnehelic pressure gauge range?

    You might want to read over the thread I started "Auger continues to feed after shutdown" (posted in June), where I pondered the best model gauge...
    Post by: jimmie ray, Aug 12, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. jimmie ray
    Post

    Should I get my stove professionally cleaned?

    In most cases, the guy you "dicker down" isn't the same guy who will do the actual cleaning. Chances are, he'll tell the service guy to finish...
    Post by: jimmie ray, Aug 11, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. jimmie ray
    Post

    Attention Regency Dealers

    My place is moving (just a few blocks away), starting tomorrow. I'm sure many items will turn up that they didn't know they had - so I'll still keep...
    Post by: jimmie ray, Jul 28, 2010 in forum: It's a Gas!
Showing results 1 to 20 of 62 Next >
Search Again
Page 1 of 4