Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
Hearth.com GOLD Sponsors who help bring the site content to you:
Jotul Cast Iron Stoves
Woodstock Soapstone Stoves
Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again

Page 1 of 3

Thread
FLAT PLATE EXCHANGER

Hi all, I need to purchase a flat plate heat exchanger to heat my shop. The shop is 150' from the house and the plate will be in the house by the...

Thread by: jimdeq, May 3, 2012, 13 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
POOL TUBE AND SHELL HEAT EXCHANGER

I installed a heat exchanger for a swimming pool to heat my shop loop. The problem I have is the exchanger is getting 180 degree water ,but it will...

Thread by: jimdeq, Apr 29, 2012, 12 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
steel fin tube radiators

I was at the salvage yard today and found some 4.5" x 4.5" steel fin tube radiators. They were 10 feet long and had a 1-1/4" pipe down the center....

Thread by: jimdeq, Mar 17, 2012, 1 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
NEW SPLITTER MOTOR QUESTION

I just bought a brand new Honda GX 270 8.5 HP motor for my splitter. I want to couple it to a 16 GPM 2 stage hydraulic pump,but need some help. I...

Thread by: jimdeq, Feb 4, 2012, 14 replies, in forum: The Gear
Thread
Heat wont shut off

Hi. I have a problem. My Tarm 60 is almost done with a full burn and my tanks are charged to 185. The problem is my house forced air zone wont...

Thread by: jimdeq, Jan 30, 2012, 8 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
NEW IN-FLOOR SETUP IN THE SHOP

I am starting the second phase of my boiler system. I want to get my shop infloor up and running. My Tarm and 1140 gallons of pressurized storage...

Thread by: jimdeq, Jan 12, 2012, 55 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
What size engine for my splitter?

I want to buy a new engine for my old homemade splitter. I currently have a old Kohler (10hp) engine that burns more oil than gas. What size engine...

Thread by: jimdeq, Dec 20, 2011, 14 replies, in forum: The Gear
Thread
SHORT BURN TIMES WITH TARM SOLO 60

I was wondering if anyone has any exprience with short burn times with there Tarm. I dont know if it is because of the 2 year seasoned hard maple or...

Thread by: jimdeq, Dec 20, 2011, 5 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
Solar Tax Question

Hi , I installed a Tarm boiler with 1100 gallons of storage and I was wondering if I also installed some solar panels would part of my system qualify...

Thread by: jimdeq, Dec 15, 2011, 4 replies, in forum: The Green Room
Thread
Anybody ever use Olympic Maximum exterior wood stain?

I was wondering if anyone has used this product. I was planning on using it for some new cedar siding.

Thread by: jimdeq, Sep 5, 2011, 4 replies, in forum: DIY and General non-hearth advice
Thread
OLD FARMHOUSE HEATING QUESTION

Hi boyz, I need help with a remodel question. I am currently renovating a old farmhouse from 1940. The home has a boiler with baseboard heat with...

Thread by: jimdeq, Sep 2, 2011, 4 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
OLD CEDAR SIDING RESTORE

Hi all, I recently purchased a charming 1940 farmhouse overlooking the water. I say charming,but not really. The home has cedar siding that is...

Thread by: jimdeq, Aug 22, 2011, 17 replies, in forum: DIY and General non-hearth advice
Thread
HOW TO REMOVE OLD PAINT?

I just bought a older home that was built in 1940. The 2 story farmhouse has cedar siding that im assuming is original. It has multiple layers of...

Thread by: jimdeq, Jun 28, 2011, 14 replies, in forum: DIY and General non-hearth advice
Thread
Summerized the Tarm

I summerized my Solo 60 for the first time today. I cleaned and vacuumed all the ash out,brushed the tubes and did a spray coat of cooking oil to...

Thread by: jimdeq, Jun 1, 2011, 5 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
9 HP Briggs problem

My very old 9 HP briggs engine keeps fouling sparke plugs. It started running rough so I shut it off,then went to restart and it wouldnt. Put in...

Thread by: jimdeq, May 16, 2011, 3 replies, in forum: The Gear
Thread
HONDA GENERATOR MOTOR ON A WOOD SPLITER?

I bought a honda EM5000 generator at a auction. I had no idea if it would even start. I got it home and it started on the first pull. I then...

Thread by: jimdeq, May 6, 2011, 11 replies, in forum: The Gear
Thread
TOO MUCH PRESSURE

I recently had my Tarm boiler and 3 storage tanks out of commission for a couple days due to warm temps. After restart I went in the basement to...

Thread by: jimdeq, Apr 17, 2011, 22 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
Very Dirty Boiler Water

I have a new pressurised system as of this winter. My storage consists of three vertical storage tanks that were from a laundramat. The tanks had a...

Thread by: jimdeq, Apr 10, 2011, 1 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
RUNNING INFLOOR OFF STORAGE TANKS?

Hi all, I want to hook up my infloor heat tubes to the boiler/storage. The infloor is in a shop 150 feet from the house. The boiler and 3 vertical...

Thread by: jimdeq, Apr 4, 2011, 19 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
Thread
HOW CAN I STOP A LEAKING FITTING? ( NEED HELP)

I have a four row water to air coil in my furnace plenum. The coil was built with 1-1/4" male adapters brazed on to the header. I cant get these...

Thread by: jimdeq, Mar 30, 2011, 23 replies, in forum: The Boiler Room - Wood Boilers and Furnaces

Showing results 1 to 20 of 59 Next >

Search Again

Page 1 of 3

Search Results

Useful Searches