1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. mhearts
    Post

    Snake on the woodpile

    Why are you standing so far away to take the picture. I can barely see the thing
    Post by: mhearts, Dec 17, 2010 in forum: The Perfect Picture
  2. mhearts
    Post

    where to tee in to existing lpg boiler

    I am running without storage. The LP Boiler would fire if temp dropped, but i have the boiler shut off so it will not. If I am away for an...
    Post by: mhearts, Dec 21, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  3. mhearts
    Post

    where to tee in to existing lpg boiler

    The LP boiler does come up to temp when the EKO loop is up to temp since one of the LP zones has a mixing valve in it to allow water to circulate...
    Post by: mhearts, Dec 20, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  4. mhearts
    Post

    where to tee in to existing lpg boiler

    correct.. there is no check between them. In the picture provided I can not locate the the return into your LP boiler.
    Post by: mhearts, Dec 18, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  5. mhearts
    Post

    where to tee in to existing lpg boiler

    It is also important that the hot water connection is below the cold return
    Post by: mhearts, Dec 18, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  6. mhearts
    Post

    where to tee in to existing lpg boiler

    Here is a picture of my setup tapping into my LP boiler. The cold water return manifold was used to make the connection. The two insulated lines...
    Post by: mhearts, Dec 18, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  7. mhearts
    Post

    Sidearm Plumbing Help Needed

    I think the pex run may be to long. Horizontal runs within the loop detract from the flow of water...Vertical runs make the delta T flow the water....
    Post by: mhearts, Dec 18, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  8. mhearts
    Post

    Couple of questions (EKO 40)

    This is the second season with my EKO40 and the first week I had it i realized there was a chance of either walking away and forgetting to close the...
    Post by: mhearts, Dec 16, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  9. mhearts
    Post

    It's 49 deg this morning

    Brrrrr...33 degrees in Saranac Lake NY last night...Look out mr tomato
    Post by: mhearts, Aug 27, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. mhearts
    Post

    EKO 40 Nozzle Erosion - first year report

    I burnt mostly ash and silver maple this winter that had been cut a year in advance. It was seasoned pretty well and was intended to be burnt in...
    Post by: mhearts, May 4, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  11. mhearts
    Post

    EKO 40 Nozzle Erosion - first year report

    Thanks for the replys. I would like to follow up with a picture. I was very careful during this years burn as to not poke or hit the nozzle while...
    Post by: mhearts, May 3, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  12. mhearts
    Thread

    EKO 40 Nozzle Erosion - first year report

    I did my spring cleaning yesterday on my EKO 40 after one full winter of burning, I noticed in the upper chamber that around the top lip of the...
    Thread by: mhearts, May 1, 2009, 13 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
  13. mhearts
    Post

    NYSERDA Launches Biomass Combustion Research Program: New Project Evaluates High-Efficiency, Wood-Fi

    Good Stuff. Thanks for sharing. I think the the state's study will quantify the minimal impact a good quality gassification boiler has on the...
    Post by: mhearts, Mar 27, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  14. mhearts
    Post

    System losing pressure - Not sure where???

    The pressure dropping when the radiator loops fills is a big clue. That indicates where the water is leaking. I would look very very closely at each...
    Post by: mhearts, Mar 11, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  15. mhearts
    Post

    EKO - Reposition Temp Sensor???

    OK ,,,I took the easier path and tried moving the sensor. I have moved it 3 times to try to narrrow the temperature difference over the past month...
    Post by: mhearts, Feb 24, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  16. mhearts
    Post

    First fire for EKO 25

    Best of luck with that first burn. The saying around my house is " You crank ...you carry" That refers to when I find the thermostat at 74 and...
    Post by: mhearts, Feb 5, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  17. mhearts
    Post

    Eko stove pipe fire

    No , it is not possible to have a stove pipe fire with the damper closed. Tightening up the door hinge will help the gasket make better contact....
    Post by: mhearts, Feb 4, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  18. mhearts
    Post

    Another what is this wood thread...

    That sure looks like Ash!
    Post by: mhearts, Dec 25, 2008 in forum: The Wood Shed
  19. mhearts
    Thread

    EKO - Reposition Temp Sensor???

    I have an EKO 40. Here is my issue. The read out on the EKO display reads 195 degrees. The actural water output temp is measured by an...
    Thread by: mhearts, Nov 23, 2008, 7 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
  20. mhearts
    Post

    Rookie Too Hot too Cold

    What size piping do you have running between the Tarm and the oil burner?
    Post by: mhearts, Nov 18, 2008 in forum: The Boiler Room - Wood Boilers and Furnaces
Showing results 1 to 20 of 30 Next >
Search Again
Page 1 of 2