1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. biohill
    Thread

    Jamestown J1000 Convection Blower

    I recently ended up with a jamestown j1000 from 1991. After vacuuming and blowing the stove out with compressed air it burns perfectly, but the...
    Thread by: biohill, Oct 22, 2012, 2 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. biohill
    Thread

    Pellet pipe question

    I recently purchased an old jamestown j1000. I want to vent it into my fireplace chimney that has been relined previously with a 5" stainless liner....
    Thread by: biohill, Oct 15, 2012, 0 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. biohill
    Thread

    5" to 4.5"x10.5" oval liner

    I am lining the chimney for installation of a hearthstone pheonix. The total height of the chimney from stove to the top is 18'. I had 25ft of oval...
    Thread by: biohill, Aug 12, 2009, 0 replies, in forum: The Hearth Room - Wood Stoves and Fireplaces
  4. biohill
    Thread

    Identify this stove, please

    I know it is an Amity, but anyone know where I could find more information?
    Thread by: biohill, Jun 23, 2009, 2 replies, in forum: The Hearth Room - Wood Stoves and Fireplaces
  5. biohill
    Post

    Geothermal Cost In Massachusetts area

    That would be excellent
    Post by: biohill, Jul 19, 2008 in forum: The Boiler Room - Wood Boilers and Furnaces
  6. biohill
    Thread

    Geothermal Cost In Massachusetts area

    Anyone have a ballpark on the cost of a geothermal system installed in MA? I am building a house next summer and trying to figure out if it is a...
    Thread by: biohill, Jul 18, 2008, 41 replies, in forum: The Boiler Room - Wood Boilers and Furnaces
  7. biohill
    Post

    Painting burn pot/ impingment baffle

    seriously, can the rustoleum high heat handle being exposed to a direct flame?
    Post by: biohill, Jul 8, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. biohill
    Thread

    Painting burn pot/ impingment baffle

    I just cleaned off all the rust from my burnpot/wearplate and baffle. Can I use rustoluem high heat to coat them? Thanks for any help!
    Thread by: biohill, Jul 8, 2008, 7 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. biohill
    Post

    Fireplace Cover

    Thanks!
    Post by: biohill, May 9, 2008 in forum: The Hearth Room - Wood Stoves and Fireplaces
  10. biohill
    Post

    Fireplace Cover

    I basically want to do what the set up in figure 1 of this link is : http://www.cnr.uidaho.edu/extforest/WFS15.pdf Sheet metal will work for this?
    Post by: biohill, May 9, 2008 in forum: The Hearth Room - Wood Stoves and Fireplaces
  11. biohill
    Thread

    Fireplace Cover

    Does anyone know where I can get a solid metal cover to put over the fireplace in my house?
    Thread by: biohill, May 9, 2008, 6 replies, in forum: The Hearth Room - Wood Stoves and Fireplaces
  12. biohill
    Thread

    25-PDV low air burn/low fuel feed question

    My stove is hooked up to a thermostat, but it was never kicking on because the stovewas cooking me of my house (only 1100sq ft) on a setting of one....
    Thread by: biohill, Jan 19, 2008, 8 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. biohill
    Post

    "Ambiance" pellets by Valfei, Are they decent?

    The salesman actually gave me an incorrect quote, when I went to check it out they were $268 a ton. No Deal
    Post by: biohill, Jan 18, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. biohill
    Thread

    "Ambiance" pellets by Valfei, Are they decent?

    I can get these for $168 a ton which is pretty damn cheap. In fact their cheapness worries me a little. They are a premium grade pellet, but I don't...
    Thread by: biohill, Jan 17, 2008, 6 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. biohill
    Post

    Any reason not to shut down my stove and clean it daily? (25-PDV)

    Another question to add, I get about two cups of black ash after burning a bag of pellets. (Granules LG brand) Is that normal?
    Post by: biohill, Dec 21, 2007 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. biohill
    Thread

    Any reason not to shut down my stove and clean it daily? (25-PDV)

    Is there any reason it would actually not be a good idea to shut down my 25-PDV and clean it daily (vaccum,scrape the burn pot and clean the glass)?
    Thread by: biohill, Dec 21, 2007, 10 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. biohill
    Post

    What is wrong with my Englander 25-PDV?

    Installed the motor yesterday. Seems to be working 100% now.
    Post by: biohill, Dec 14, 2007 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. biohill
    Post

    What is wrong with my Englander 25-PDV?

    Done
    Post by: biohill, Dec 12, 2007 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. biohill
    Post

    What is wrong with my Englander 25-PDV?

    sorry , just saw the post , i see you did talk to one of my techs and they have new motor in route, gawd, i have no time these days! let me know...
    Post by: biohill, Dec 12, 2007 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. biohill
    Post

    Timberidge 55-TRP22 Remote Thermostat

    I installed a wall thermostat, does it matter which wire goes in which terminal on the stoves board? The wire I used is two wire thermostat wire with...
    Post by: biohill, Dec 11, 2007 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 33 Next >
Search Again
Page 1 of 2