1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
  1. Holley
    Post

    Garn Tank and Supply Temp ?????

    Yes you could but it wouldn't be as accurate. Really depends on how close you can get...You'd want to compare the temperature the aquastat was...
    Post by: Holley, Jan 30, 2013 in forum: The Boiler Room - Wood Boilers and Furnaces
  2. Holley
    Post

    Garn Tank and Supply Temp ?????

    I talked for a few minutes with the folks at Dectra and for now I think the best location for a sensor controlling a backup boiler is in a 12" deep...
    Post by: Holley, Jan 30, 2013 in forum: The Boiler Room - Wood Boilers and Furnaces
  3. Holley
    Post

    Garn Tank and Supply Temp ?????

    Heaterman thanks for your kind words earlier. Rob, the link for the intake air damper is http://shop.garn.com/garn-model-2000-1989-present/. The...
    Post by: Holley, Jan 30, 2013 in forum: The Boiler Room - Wood Boilers and Furnaces
  4. Holley
    Post

    Garn Tank and Supply Temp ?????

    The Alpha smart pumps are magic. As Heaterman said, even in a constant mode they use much less power than a conventional wet rotor pump. And they...
    Post by: Holley, Jan 29, 2013 in forum: The Boiler Room - Wood Boilers and Furnaces
  5. Holley
    Post

    Garn Tank and Supply Temp ?????

    Here's Jim's piping plan. I just spoke with Jim and you guys nailed it..it's clearly a stratification issue. I believe Jim first saw this happen...
    Post by: Holley, Jan 28, 2013 in forum: The Boiler Room - Wood Boilers and Furnaces
  6. Holley
    Post

    Garn Controller Wiring - Anyone change it? Look at the Grounds

    Have another look at that controller. The neutral and ground are most assuredly NOT tied together. One leg of the 24 volt side of the transformer...
    Post by: Holley, Dec 13, 2011 in forum: The Boiler Room - Wood Boilers and Furnaces
  7. Holley
    Post

    My Garn Corrosion Fiasco Part 1

    I am grateful Rick took the time to document and post his corrosion issue and how he corrected it. When I first saw Rick's photos he was well into...
    Post by: Holley, Feb 10, 2011 in forum: The Boiler Room - Wood Boilers and Furnaces
  8. Holley
    Post

    Garn connection to existing boiler question

    Thanks Chris, it is a tankless domestic hot water coil. The temperature is controlled by an aquastat. Luckily the system has been running...
    Post by: Holley, Aug 20, 2010 in forum: The Boiler Room - Wood Boilers and Furnaces
  9. Holley
    Post

    Garn connection to existing boiler question

    Well that was a nice gift George :) That LA14-50X is already over-sized for your application. I generally design radiant systems around a 15 degree...
    Post by: Holley, Aug 17, 2010 in forum: The Boiler Room - Wood Boilers and Furnaces
  10. Holley
    Post

    Garn connection to existing boiler question

    Yes George, the configuration you have shown will work. With the right design flow rates and heat exchanger selection it is also possible to cut...
    Post by: Holley, Aug 16, 2010 in forum: The Boiler Room - Wood Boilers and Furnaces
  11. Holley
    Post

    Garn WHS3200 Performance Experience - Part 1 & 2 merged

    Jim, the burn-rate based on an hourly load info is in all of GARN brochures and in the specification sheet in the Installation manual that was packed...
    Post by: Holley, Jun 4, 2010 in forum: The Boiler Room - Wood Boilers and Furnaces
  12. Holley
    Post

    Garn WHS3200 Performance Experience - Part 1 & 2 merged

    Jim, I'm the rep for GARN for New England and the Eastern Provinces. We have a 3200 operating heating a large assisted living center in Vermont...
    Post by: Holley, Jun 3, 2010 in forum: The Boiler Room - Wood Boilers and Furnaces
Showing results 1 to 12 of 12
Search Again