1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 4
  1. pfmaloney
    Post

    Accentra Insert Igniter

    Thank you for the replies. I will bring this up with my dealer.
    Post by: pfmaloney, Feb 13, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. pfmaloney
    Post

    Accentra Insert Igniter

    Unfortunately, I can't test the igniter at the moment since it's fried. If the triac or control board were suspect, would that be detected by...
    Post by: pfmaloney, Feb 12, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. pfmaloney
    Post

    Accentra Insert Igniter

    I've been happy with the consistent room temperature that room temp mode delivers. While in Room Temp mode, my accentra has never turned off and...
    Post by: pfmaloney, Feb 12, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. pfmaloney
    Thread

    Accentra Insert Igniter

    Well, there goes another igniter! This is the fourth igniter that has failed in my Accentra Insert in the two years that I have owned it....
    Thread by: pfmaloney, Feb 12, 2013, 12 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. pfmaloney
    Post

    Any benefit to an insert over a free standing stove?

    I don't believe that website is referring to Pellet stoves/inserts, but rather wood burning ones.
    Post by: pfmaloney, Oct 12, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. pfmaloney
    Post

    Extending Harman Room Temp Probe

    I extended it around 15 feet as well and have it at eye level while sitting down. I have a digital thermostat near the probe and have been...
    Post by: pfmaloney, Aug 31, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. pfmaloney
    Post

    Extending Harman Room Temp Probe

    During our installation, I had the tech extend the wire and he used wire connectors like the ones used in the back of the unit.
    Post by: pfmaloney, Aug 31, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. pfmaloney
    Post

    Pam Cooking Spray Question

    I have an Accentra insert. I seal off the OAK where it terminates on the outside wall with gorilla tape, to prevent the humid air, as well as bugs...
    Post by: pfmaloney, May 23, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. pfmaloney
    Post

    Harman Accentra or Mt Vernon

    Great looking setup, you'll enjoy your Harman.
    Post by: pfmaloney, Apr 13, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. pfmaloney
    Post

    harman heat exchanger buildup?

    I bought a detail brush kit from Pep Boys for $5. It includes a stainless steel brush that does a great job cleaning the recessed sections of the...
    Post by: pfmaloney, Mar 5, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. pfmaloney
    Post

    Advice on Insert / CT Dealers

    Here are a couple of things to consider regarding these inserts. The Harman and the Enviro M55 inserts slide out on rails when you want to do a deep...
    Post by: pfmaloney, Feb 24, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. pfmaloney
    Post

    Another Room/Stove Temp Question on Accentra Insert?

    According to our installer, the draft reading was spot on, but our flame is quite strong, i.e. a blow torch when going full bore. Since we have an...
    Post by: pfmaloney, Feb 22, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. pfmaloney
    Post

    Harman Accentra Insert

    I set the fan in the middle position between L and H. I prefer Room Temp mode since it provides a consistent temperature regardless of the outside...
    Post by: pfmaloney, Feb 17, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. pfmaloney
    Post

    Manual or auto

    Bad news. I spoke to the dealer this morning and they said that both the failed and new igniter are the newer 15 fin model. The mystery remains...
    Post by: pfmaloney, Feb 3, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. pfmaloney
    Post

    Manual or auto

    Hopefully, the "new" igniter is new!!
    Post by: pfmaloney, Feb 2, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. pfmaloney
    Post

    Manual or auto

    This is certainly a timely topic for me. My accentra insert was installed last February. I normally run it in Room Temp/Auto mode 24x7. Since I am...
    Post by: pfmaloney, Feb 2, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. pfmaloney
    Post

    Flame Guard Harman Accentra

    Are you sure the flame guard is on correctly? During your normal cleaning, do you brush the grooves on the flame guide that rest on the burn pot ?...
    Post by: pfmaloney, Jan 15, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. pfmaloney
    Post

    harman accentra insert ?

    Yes, you can clean the tubes without removing the ESP probe. In fact, in the Harman installation manual it lists cleaning the tubes before it...
    Post by: pfmaloney, Jan 8, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. pfmaloney
    Post

    harman accentra insert ?

    Do you clean the chamber on the bottom of the burn pot where the ignitor wires are located while the power is ON?
    Post by: pfmaloney, Jan 7, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. pfmaloney
    Post

    harman accentra insert ?

    so, now you can see the brush from right side when cleaning the left?
    Post by: pfmaloney, Jan 5, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 76 Next >
Search Again
Page 1 of 4