1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 3
  1. Eric Bommer
    Thread

    Its a Bird, Its a plane, its my new Toro leaf blower

    I want to thank Imacman for his recommendation for getting a leaf blower to clean my stove. What difference and how easy. I thought I was very good...
    Thread by: Eric Bommer, Feb 11, 2013, 8 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. Eric Bommer
    Post

    A Manometer and my 55-TRPEP

    Thanks for the advice. I sent Mike a note, hopefully he is not to swamped right now with the busy time of year.
    Post by: Eric Bommer, Feb 7, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. Eric Bommer
    Thread

    A Manometer and my 55-TRPEP

    As many of you have tried to help me get my stove dialed in, I have been thinking that I need to get something that will give me a number telling me...
    Thread by: Eric Bommer, Feb 6, 2013, 2 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. Eric Bommer
    Post

    Looking for a leaf blower

    Thanks for all of the feed back. Looking at the Menards web site I can get a pretty cheap Weed Eater blower/vacuum for $40.00 that has a 12 amp...
    Post by: Eric Bommer, Jan 29, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. Eric Bommer
    Thread

    Looking for a leaf blower

    I have heard several times of the benefit of using a leaf blower to clean out a pellet stove. Any recommendation. Gas vs Electric, Brand, ect.
    Thread by: Eric Bommer, Jan 29, 2013, 30 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. Eric Bommer
    Post

    So what happens if you don't have 1/4" per foot in a horizontal pipe

    I am doing that now. If its only a matter of ash, after 3 weeks and 30 bags I only had about 1/8 inch of ash in a 4 inch pipe from today's cleaning....
    Post by: Eric Bommer, Jan 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. Eric Bommer
    Thread

    So what happens if you don't have 1/4" per foot in a horizontal pipe

    So after all the comments I received about having a 1/4 inch rise per foot of horizontal pipe, today was really nice so I took off the end cap and...
    Thread by: Eric Bommer, Jan 26, 2013, 4 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I just found another manual for Lennox Hearth Product also list a max of 10 feet horizonal. I am not saying its a good idea it just a dimension list...
    Post by: Eric Bommer, Jan 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. Eric Bommer
    Post

    Unable to get high pellet feed rate

    If you look at my post again I did give the sources: 10 feet of horizontal is from Woodpelletheat.com a company out of Canada. I guess without data...
    Post by: Eric Bommer, Jan 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I just found this From Englander: 1. We require a minimum vertical rise of 36 in.(I'm good here) 2. Venting systems 15.0 ft. or shorter may be...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I am really not sure how I or anyone else can go much shorter then 48". I have about 12" from the back of the stove to the wall another 12" for wall...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I just check it from inside with a level and I would estimate a 1/4" to 3/8" rise over the 4 feet(I have approximately 2 feet on each side of the...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. Eric Bommer
    Post

    Unable to get high pellet feed rate

    Also if it helps I am using Selkirk 4" double wall vent pipe(exhaust on the inside, fresh air on the out side). From the stove I go to a clean out...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. Eric Bommer
    Post

    Unable to get high pellet feed rate

    Maybe you do know the stove. it was a refurbished unit :) Right now I have the stat set to 90 to have it run continuous just trying to find out...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. Eric Bommer
    Post

    Unable to get high pellet feed rate

    And I have also removed the plate covering the heat exchanger tube and cleaned with an old paint brush then vacuumed up the ashes,
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. Eric Bommer
    Post

    Unable to get high pellet feed rate

    Sorry I change my stove more from a 3 to a 2
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. Eric Bommer
    Post

    Unable to get high pellet feed rate

    My last issue was a feed issue, My stove was set to a 3 and Mike had me drop it down to a 2. So I was over feeding the system at all feed rates.
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I have had this issue since almost the beginning. I worked with Mike from Englander around Christmas and he did find my mode was set incorrectly...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. Eric Bommer
    Post

    Unable to get high pellet feed rate

    I also replaced all of my gaskets this year and did the flame test for leaks around all of the areas with gaskets and found no leaks. Also from last...
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. Eric Bommer
    Post

    Unable to get high pellet feed rate

    Yes exactly, I am currently set at 1,5,1,
    Post by: Eric Bommer, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 41 Next >
Search Again
Page 1 of 3