1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 2
  1. AndyL
    Post

    enviro ef2 auger

    The pellets could be the problem but I doubt it. The pellets don't seem overly large or too hard and burn very well in my dell.point, Danson v50i...
    Post by: AndyL, Jan 7, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. AndyL
    Post

    enviro ef2 auger

    No responses? I have been burning pellets for 4 years, reading this forum 2 years, and have been posting for a year. This is a legitimate problem....
    Post by: AndyL, Jan 6, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. AndyL
    Thread

    enviro ef2 auger

    I Have an ef2 that is about three months old the auger seems to jam on the pellets. Sometimes hard enough to stop feeding pellets completely, other...
    Thread by: AndyL, Jan 6, 2009, 4 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. AndyL
    Post

    Enviro EF2 insert

    Here is a website for the enviro trouble shooting manual from Hearth tools .com http://www.hearthtools.com/parts/2004enviroTrouble.pdf Go to page 2...
    Post by: AndyL, Dec 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. AndyL
    Post

    Enviro EF2 insert

    In short no. One of My other stoves has one built in on the control panel. I checked the enviro with it but I just assume adjusting it by eye. Try...
    Post by: AndyL, Dec 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. AndyL
    Post

    Enviro EF2 insert

    Also the damper rod may have a lock collar with a set screw on the back of the panel to prevent it from being bumped out of adjustment accidentally.
    Post by: AndyL, Dec 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. AndyL
    Post

    Enviro EF2 insert

    Mechanically it will work just don't use too much it will make it hard to get the blower off. When You do take the blower back off to replace the...
    Post by: AndyL, Dec 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. AndyL
    Post

    Enviro EF2 insert

    No, never had that problem. Sounds like your combustion air is dampened down to low causing a lousy burn. try opening up your air damper and getting...
    Post by: AndyL, Dec 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. AndyL
    Post

    Enviro EF2 insert

    It's on the top port on mine.
    Post by: AndyL, Dec 6, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. AndyL
    Post

    Pellet Stove

    Was this stove proffesionally installed? If its not installed properly you could be getting flue gas in Your home. If you don't have a carbon...
    Post by: AndyL, Nov 30, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. AndyL
    Post

    Enviro EF2-I FRUSTRATION!!!

    Outside air is a required setup in a mobile home, call your dealer and demand it be installed. however for now try cracking a window near the stove...
    Post by: AndyL, Nov 23, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. AndyL
    Post

    Enviro EF2-I FRUSTRATION!!!

    If You have outside air there should be a second section of tube running to the outside, It connects to the bottom center of the rear of the stove...
    Post by: AndyL, Nov 23, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. AndyL
    Post

    Enviro EF2-I FRUSTRATION!!!

    Just a quick question, Do you have outside air installed?
    Post by: AndyL, Nov 23, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. AndyL
    Post

    Newbie Question - Danson Pellet Top Loader: Not feeding

    Check the hi limit safety switch. It should be a snap disk type switch mounted on the back side of the firebox and it might be manually resettable....
    Post by: AndyL, Nov 22, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. AndyL
    Post

    Newbie Question - Danson Pellet Top Loader: Not feeding

    Another question does the "auger cycle" light blink occasionally indicating that the control is calling for pellets? Can you visually confirm that...
    Post by: AndyL, Nov 22, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. AndyL
    Post

    Newbie Question - Danson Pellet Top Loader: Not feeding

    Hi, When you are starting your stove The door is closed? correct! If so it could be a blocked vacuum switch. the switch monitors the pressure...
    Post by: AndyL, Nov 21, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. AndyL
    Post

    Should I buy a Dell Point 75?

    I Have one , the multifuel model. I love it runs quite and very hot. I'M not so worried by what you refer to as its orphan status as there are...
    Post by: AndyL, Jul 20, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. AndyL
    Post

    Anyone have a PelPro Pellet Stove?

    Hi, I have three Pelpro stoves in the family. The stoves are going on 4 years old and I have not had any major issues with the stoves that have...
    Post by: AndyL, Mar 19, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. AndyL
    Post

    The never ending....overflowing burn pot?

    Hi, Check to see if your burn grate is warped it should fit into the burn pot without any gaps in the front, side or rear. If you have gaps it...
    Post by: AndyL, Mar 5, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. AndyL
    Post

    Dell-Point start up sequence

    Jerry, I also have the multi-fuel model. I did say the start button, I should have said the fuel selector button. The fuel in my case is...
    Post by: AndyL, Feb 7, 2008 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 25 Next >
Search Again
Page 1 of 2