1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 10
  1. CJ-SR4ever
    Post

    Low draft adjustment screw

    I would take a look at you hopper lid gasket. If it is not sealed tightly or if there is a pellet or two caught in the gasket it will whistle a bit.
    Post by: CJ-SR4ever, Nov 7, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. CJ-SR4ever
    Post

    pellet 3" horizontal thimble question

    Shouldnt use alot of silicone unless you got 3 inch pipe going through a 4 inch thimble. If sealing the inside portion of the thimble is easier you...
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. CJ-SR4ever
    Post

    Anyone know whats wrong with my Pellet Stove?

    The high heat is wearing away the metal. I have seen this with other stoves. Contact your local dealer to replace the feeder body weldment. This...
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. CJ-SR4ever
    Post

    cleaning glass with baby wipes

    I also just use a wet paper towel with water and a little dip in the ash to get those hard spots.
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. CJ-SR4ever
    Post

    pellet 3" horizontal thimble question

    Seal around the pipe on the exterior thimble with high temp silicone. You are not missing any parts. That is normal for ICC.
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. CJ-SR4ever
    Post

    Harman Accentra Insert Ignitor stuck on

    Your ignitor staying in doesnt exactly mean your control board is bad. Sounds more like an ESP issue to me. Have you cleaned the ESP in the off...
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. CJ-SR4ever
    Post

    cleaning glass with baby wipes

    Baby wipes? Hmmmmm, thats something I never thought of, got plenty of them around. I will give that a try when the wife aint looking. lol
    Post by: CJ-SR4ever, Nov 6, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. CJ-SR4ever
    Post

    Sparks / ash

    So thats what your supposed to do with your bush? Thanks Hermit, I will give that a try. LOL. On a serious note......I have my share of sparks...
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. CJ-SR4ever
    Post

    Thermostat plug connections

    I have the basic Honeywell thermostat running my Lennox Montage and the wire I used has a red and white. I used the R and W on my thermostat and it...
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. CJ-SR4ever
    Post

    Is there any existing thermostat shutoff device for when a pellet stove goes on UPS?

    Not that I know of. Would be a neat idea though. If I lose power in my home, I disconnect the thermostat and just run the stove straight out....
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. CJ-SR4ever
    Post

    Photoeye Question on My profile 20 pellet stove?

    Hmmm, What I would do to test it would be to, after the stove lights, gently lift the cover that holds the photoeye and shine a flashlight at it...
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. CJ-SR4ever
    Post

    Profile 20 Control Board Bad??

    Sounds like a bad control board indeed. I have encountered this a few times and a new control board will be needed. Did you leave it plugged in...
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. CJ-SR4ever
    Post

    Photoeye Question on My profile 20 pellet stove?

    Is your photoeye located in the hopper or behind the stove? You may be able to test it by exposing it to light. Have you checked the little slot...
    Post by: CJ-SR4ever, Nov 5, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. CJ-SR4ever
    Post

    Harman Hopper Extension

    I would love one on my P 38. Dont care about looks, just care about being warm!!! I have heard many good things about them.
    Post by: CJ-SR4ever, Nov 4, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. CJ-SR4ever
    Post

    Thermostat plug connections

    Your welcome. Enjoy the heat! I hope this early october snow storm is not a sign of things to come this winter!
    Post by: CJ-SR4ever, Nov 4, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. CJ-SR4ever
    Post

    Thermostat plug connections

    If you are refering to the plug that looks like a phone cable plug, that one is for plugging in the diagnostics box for troubleshooting. There is 2...
    Post by: CJ-SR4ever, Nov 4, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. CJ-SR4ever
    Post

    Harman P43 Air Flow / Left Side Burn Issues

    Check the burn pot holes, check inside of the burn pot make sure it is clear of ash, and if there is ash stuck in the ignitor that can also affect...
    Post by: CJ-SR4ever, Nov 4, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. CJ-SR4ever
    Post

    Harman - Distribution Blower Fluctuating in Speed

    The control board does have the ability to over-ride the blower speed you have set. Depending on the temp the ESP is reading and the stove set point...
    Post by: CJ-SR4ever, Oct 26, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. CJ-SR4ever
    Post

    Wall thimble issue

    Check to see if the brand that makes that wall thimble also makes a wall thimble extention. I know of a few brands that make those. Its worth...
    Post by: CJ-SR4ever, Aug 22, 2011 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. CJ-SR4ever
    Post

    tfdchief injured in accident

    Sorry to hear about your accident. Get well soon! Glad you are still here with us.
    Post by: CJ-SR4ever, Jul 11, 2011 in forum: The Inglenook
Showing results 1 to 20 of 198 Next >
Search Again
Page 1 of 10