1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 5
  1. DannMarr
    Post

    Propane tank valve lock

    Just a question: Why is it OK when the gas company puts on a lock on the tank? Isn't that also a dangerous concern?
    Post by: DannMarr, Jan 30, 2011 in forum: It's a Gas!
  2. DannMarr
    Post

    Super Clinkers

    For me, I need to empty my pot twice a day to avoid clinkers. Yes I'm using Tree Cycle, can't wait for them to run out. They don't produce much heat....
    Post by: DannMarr, Jan 16, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. DannMarr
    Post

    Swing setting?

    Thanks! I have it set at 9 as some have suggested to get that 2 degree swing. At 70 degrees set point, sometimes it will turn on at 68, 67 and even...
    Post by: DannMarr, Jan 11, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. DannMarr
    Thread

    Swing setting?

    I have a Castille insert and a Lux thermostat. The thermostat works fine but inconsistent when using the swing options. It seems to me that this...
    Thread by: DannMarr, Jan 11, 2010, 3 replies, in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. DannMarr
    Post

    Yes ---another OAK question

    I went up the chimney, but not all the way. I insulated the bottom where the damper used to be, to prevent any cold air from coming down the chimney....
    Post by: DannMarr, Jan 8, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. DannMarr
    Post

    Yes ---another OAK question

    I have a Quadrafire Castile insert. I originally had no fresh outside air. The insert would pull in air from within the home and cause a draft along...
    Post by: DannMarr, Jan 8, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. DannMarr
    Post

    Quadrafire 1200-i blower speed?

    Yes, on my Castile insert the feed rate is linked with the burn rate, low med, high.
    Post by: DannMarr, Jan 6, 2010 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. DannMarr
    Post

    Quad Castille FS will not feed

    Original problem after suggestion to check voltage again ?????????????????????????? :ohh: It's hard to help when the information given is...
    Post by: DannMarr, Dec 31, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. DannMarr
    Post

    Quad Castille FS will not feed

    Original problem solved problem ?????????????? :ohh:
    Post by: DannMarr, Dec 31, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. DannMarr
    Post

    Quadrafire won't power up

    Set your thermostat to get the red light to come on. Get yourself a voltmeter, set it to AC volts. Put the black probe on a solid metal surface....
    Post by: DannMarr, Dec 30, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. DannMarr
    Post

    Quadrafire won't power up

    I agree, stop replacing parts unless you are sure they are bad. If you have a volt meter, check voltage before and after the snap disk and the vacuum...
    Post by: DannMarr, Dec 30, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. DannMarr
    Post

    Bench Testing an Ignitor

    If it reads indefinitely, then it's bad.
    Post by: DannMarr, Dec 29, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. DannMarr
    Post

    Feed Rate

    On our inserts, the control box controls both the feed rate together with the fan speed. If we can isolate the fan with its own dedicated switch...
    Post by: DannMarr, Dec 29, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. DannMarr
    Post

    Quadrafire won't power up

    You need to check for power with a volt meter. The items before the thermostat screws are what needs to be tested, The fuse, the connecters and the...
    Post by: DannMarr, Dec 29, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. DannMarr
    Post

    Advice Needed After Chimney Inspection on Gas Fireplace

    I have a buyer and they are aware of the chimney flue. I left the damper intact in case they need to crack it open for venting (fresh air intake). I...
    Post by: DannMarr, Dec 26, 2009 in forum: It's a Gas!
  16. DannMarr
    Post

    Opinions on electric heaters like Eden pure etc

    I own one of those iHeaters. It will not heat up a whole house, or a large open area either. It does work well in a small bedroom with low ceilings...
    Post by: DannMarr, Dec 26, 2009 in forum: The Green Room
  17. DannMarr
    Post

    Advice Needed After Chimney Inspection on Gas Fireplace

    I bought a house to flip and encountered the same problem. I had the chimney guy come over to give it a cleaning. He said it needed a new liner and...
    Post by: DannMarr, Dec 26, 2009 in forum: It's a Gas!
  18. DannMarr
    Post

    Pex. Hottest Temp

    There is another type of pex that has an aluminum liner inside, I believe it's for stronger/hotter applications. I saw it on the counter at an HVAC...
    Post by: DannMarr, Dec 26, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  19. DannMarr
    Post

    Pipe Dope or Teflan tape?

    I agree with fyrewerks and webby, I never mix. Tape or paste work fine as long as you use it properly for the right application.
    Post by: DannMarr, Dec 26, 2009 in forum: The Boiler Room - Wood Boilers and Furnaces
  20. DannMarr
    Post

    Does blower speed effect burn rate? (He said, she said)

    I stand correct on my earlier assumption, the convection fan speed set on high will burn more pellets. The Convection blower fan speed is used in...
    Post by: DannMarr, Dec 25, 2009 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 95 Next >
Search Again
Page 1 of 5