1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 10
  1. stoveguy13
    Post

    Liability with providing service

    you touched it last you own it. when you go to service or clean it. you take over the liability for the install good or bad.
    Post by: stoveguy13, Aug 2, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. stoveguy13
    Post

    burn pot overflowing

    you know, it never was set with a mag. I have read about that, and i am certain the installer did NOT do that. His directions as far as the damper...
    Post by: stoveguy13, Feb 3, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. stoveguy13
    Post

    Jotul Combi #1

    dose it have a listing plate on it?
    Post by: stoveguy13, Feb 3, 2012 in forum: Classic Wood Stove Forums Pre-EPA (prior to 1988)
  4. stoveguy13
    Post

    thermostat weirdness

    cant read the thermo but it might not be calibrated right if it doesnt bother you dont worry about it if it does may want to get a ne thermo
    Post by: stoveguy13, Feb 3, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. stoveguy13
    Post

    burn pot overflowing

    it is an airflow/dirty issue has the stove ever been set with a mag.?
    Post by: stoveguy13, Feb 2, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. stoveguy13
    Post

    The Hearthstone "Heritage" model Pellet stove

    they had some blower issues with the first group but worked through that now the only real down side to the stove i found running it was the hopper...
    Post by: stoveguy13, Feb 2, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. stoveguy13
    Post

    m55 cast insert - stirrer grinding 2 days after GOOD cleaning

    It always happens eventually. This time it happened only 3 days after cleaning. maybe poor quality pellets?[/quote] it could be the pellets it...
    Post by: stoveguy13, Jan 27, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. stoveguy13
    Post

    Can't Figure Out How A Piggybacked Pellet Boiler Would Work With An Oil Boiler

    no problem!!!
    Post by: stoveguy13, Jan 27, 2012 in forum: The Boiler Room - Wood Boilers and Furnaces
  9. stoveguy13
    Post

    installing insert into zero-clearance prefab... removing refractory panels?

    NO WAY!!! do not remove them
    Post by: stoveguy13, Jan 27, 2012 in forum: The Hearth Room - Wood Stoves and Fireplaces
  10. stoveguy13
    Post

    JOTUL KENNEBEC OVERFIRING?

    650 is not too hot
    Post by: stoveguy13, Jan 26, 2012 in forum: The Hearth Room - Wood Stoves and Fireplaces
  11. stoveguy13
    Post

    Can't Figure Out How A Piggybacked Pellet Boiler Would Work With An Oil Boiler

    sent you pm
    Post by: stoveguy13, Jan 26, 2012 in forum: The Boiler Room - Wood Boilers and Furnaces
  12. stoveguy13
    Post

    Can't Figure Out How A Piggybacked Pellet Boiler Would Work With An Oil Boiler

    auto / manual mode refer to the igniton not to how it runs the the simplest way to get what you want would be to plumb the hydro in to the return of...
    Post by: stoveguy13, Jan 26, 2012 in forum: The Boiler Room - Wood Boilers and Furnaces
  13. stoveguy13
    Post

    m55 cast insert - stirrer grinding 2 days after GOOD cleaning

    does it happen all the time? or just sometimes? what fuel setting are you on?
    Post by: stoveguy13, Jan 26, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. stoveguy13
    Post

    Soft Wood Pellet Setting Mount Vernon AE

    hardwood has more air and less feed so whatever one works better is the one i would use if you want to run on softwood you could also try adjusting...
    Post by: stoveguy13, Jan 16, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. stoveguy13
    Post

    castile problem

    you could try checking the set screw it holds the auger spring to the shaft of the motor if it comes loose the motor turns but the spring does not
    Post by: stoveguy13, Jan 16, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. stoveguy13
    Post

    Hampton HI300 airflow problem?

    if it is working i wouldnt mess with it
    Post by: stoveguy13, Jan 15, 2012 in forum: The Hearth Room - Wood Stoves and Fireplaces
  17. stoveguy13
    Post

    Hampton HI300 airflow problem?

    have you changed anything in the house ? also if your wood is wetter then it was last year that could be causing the stove to not operate the same....
    Post by: stoveguy13, Jan 15, 2012 in forum: The Hearth Room - Wood Stoves and Fireplaces
  18. stoveguy13
    Post

    Tech Issue with BOSCA Soul 500 insert - need help/opinion

    i have had a few boscas over feed and it was an air supply issue not a control board issue what fixed them was the door gasket may be worth trying
    Post by: stoveguy13, Jan 15, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. stoveguy13
    Post

    M55 Error #3

    Put both feed an air on 3
    Post by: stoveguy13, Jan 13, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. stoveguy13
    Post

    M55 Error #3

    The most common #3 error I see is related To damper setting as J said can't hurt But have it set with the mag.
    Post by: stoveguy13, Jan 13, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 200 Next >
Search Again
Page 1 of 10