1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 3
  1. jasong
    Post

    Digital LED temp readout and alarm installed

    I have had 2 PID controllers on my stove for a couple of years now. One thermocouple is inserted in the stove pipe and one is held down to the stove...
    Post by: jasong, Nov 20, 2011 in forum: The Hearth Room - Wood Stoves and Fireplaces
  2. jasong
    Post

    Installing a wood stove need floor help

    I installed a Summers Heat 13nc also in a mobile home. I took steel studs, welded them together. I put 3 layers of cement board with a sheet of thin...
    Post by: jasong, Oct 10, 2011 in forum: The Hearth Room - Wood Stoves and Fireplaces
  3. jasong
    Post

    PO’d

    Yeah I definitely learned my lesson. It won't happen again.
    Post by: jasong, Feb 15, 2011 in forum: The Wood Shed
  4. jasong
    Post

    PO’d

    That would be well and good except it didn't get donated to the church.
    Post by: jasong, Feb 15, 2011 in forum: The Wood Shed
  5. jasong
    Thread

    PO’d

    Went to my church to cut up a tree that had died and was going to use it for firewood since I use solely wood for heat. I spent an hour and a half...
    Thread by: jasong, Feb 15, 2011, 21 replies, in forum: The Wood Shed
  6. jasong
    Post

    Why Are Outside Air Kits are So Expensive

    I went with aluminum dryer vent transitioned into dwv pvc and used a pvc floor drain in the end of the dwv. When the stove is burning good and you...
    Post by: jasong, Oct 27, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  7. jasong
    Post

    How do I remove a simpson chimney cap?

    Why not untwist the top section that has the chimney cap on it. And put the new section where that one came off. Then put the section you took off...
    Post by: jasong, Feb 6, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  8. jasong
    Post

    Condar Temp Probe vs. The Thermocouple...

    I needed a good steady heat source that I new the temperature of. It worked well. It was kind of a pain. when it's loosened you can match the dial to...
    Post by: jasong, Feb 1, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  9. jasong
    Post

    Condar Temp Probe vs. The Thermocouple...

    I have a Condar flueguard probe and digital thermocouple alarms on stove and flue. What I have seen with the Condar is that it is extremely slow on...
    Post by: jasong, Feb 1, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  10. jasong
    Post

    How much wood do you have left?

    I still have 5 1/2 cords left. I cut up but didn't split about two more cords last weekend. I didn't need it. It was free and they were going to burn...
    Post by: jasong, Jan 8, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  11. jasong
    Post

    Blower motor humming Now not turning

    CleamBurnin is right. Most fans have to be lubricated. A few drops of oil on the bearings might fix it.
    Post by: jasong, Jan 4, 2010 in forum: The Hearth Room - Wood Stoves and Fireplaces
  12. jasong
    Post

    Englander 13 Not throwing heat.....

    I can't close the air down completely on my 13. From what I have read on here this is mostly the case with the 13 and the 30. I close it down all the...
    Post by: jasong, Dec 31, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  13. jasong
    Post

    How to quickly get stove temp back down

    You don't say what kind of stove you have. On mine I have put aluminum foil over the main air intake. It chokes it down to no flame in a mater of...
    Post by: jasong, Dec 30, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  14. jasong
    Post

    Englander 13 Not throwing heat.....

    Did you clean your chimney after burning last year?
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  15. jasong
    Post

    Englander 13 Not throwing heat.....

    My OAK does not help me get longer burn times. If the crawl space can supply enough air to feed your fire I think it would be alright.
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  16. jasong
    Post

    Englander 13 Not throwing heat.....

    It's the same stove but mine has the outside air kit hooked up. Draft would be affected by length of the chimney and flue. The oak would only supply...
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  17. jasong
    Post

    Englander 13 Not throwing heat.....

    Use a straight edge to check the door and plate where the door should seal.
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  18. jasong
    Post

    Englander 13 Not throwing heat.....

    With a full load of oak I get 3 to to 5 hours of actual flames with the same stove.
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  19. jasong
    Post

    Englander 13 Not throwing heat.....

    Either your gasket is bad or the door or stove face is warped. This would cause you to not be able to control your fire and burn the wood up fast but...
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
  20. jasong
    Post

    Englander 13 Not throwing heat.....

    Do you have any thermometers on the stove or flue? What do you you mean by you being able to see into the stove from the top with the door closed?
    Post by: jasong, Dec 5, 2009 in forum: The Hearth Room - Wood Stoves and Fireplaces
Showing results 1 to 20 of 51 Next >
Search Again
Page 1 of 3