1. Welcome Hearth.com Guests and Visitors - Please enjoy our forums!
    Hearth.com GOLD Sponsors who help bring the site content to you:
    Jotul Cast Iron Stoves
    Woodstock Soapstone Stoves
    Hearth and Home (QuadraFire and Harman Stoves)

Search Results

Search Again
Page 1 of 10
  1. rona
    Post

    Indecision over pellet or wood, insert or stove

    I think a freestanding Quad Sante Fe will be your best choice of the ones you listed. Freestanding because easier maintenence, it holds more...
    Post by: rona, May 11, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  2. rona
    Post

    Indecision over pellet or wood, insert or stove

    Post by: rona, May 11, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  3. rona
    Post

    vent smoke

    The big reason for the vertical whether or not it is inside or outside is to creat a draft so if the stove is shut off the smoke will continue to...
    Post by: rona, Apr 3, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  4. rona
    Post

    vent smoke

    Before you spend big bucks with new pipe inside the chimney I would try it the cheap way and see for yourself. The only problem I could see is if...
    Post by: rona, Apr 2, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  5. rona
    Post

    vent smoke

    It will run fine. Think of it for a minute people run a 3 inch 2 feet long before it is outside the wall. You are going from a 3 inch into a 6...
    Post by: rona, Mar 31, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  6. rona
    Post

    Pellet pricing - what would you do?

    Indeck found in Minn at Menards 173.50 Mar 22.
    Post by: rona, Mar 31, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  7. rona
    Post

    Running 2 pellet stoves

    I doubt you would be happy with it since it will shut off both stoves at the same time and most of the time with two stoves one end of the house...
    Post by: rona, Mar 3, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  8. rona
    Post

    new guy

    Buy a good surge protecter. I would also read through this website and see if you can determine what type of dealers are in your area. Patronize...
    Post by: rona, Feb 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  9. rona
    Post

    Pellet boiler Kit??

    Which safety checks were over looked? My ins company had more questions about the stove then the kit that was put in after they seen the stove....
    Post by: rona, Feb 26, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  10. rona
    Post

    Pellet boiler Kit??

    Google Crosslink Conversions- send him a e-mail saying you would like to talk with him and ask Him your questions. I am not a salesman but having...
    Post by: rona, Feb 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  11. rona
    Post

    Pellet boiler Kit??

    Does it work like you expected? I do agree it is high priced for what you get but how much profit does a dentist make on one tooth these days....
    Post by: rona, Feb 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  12. rona
    Post

    Advice on install for pellet stove near baseboard heat?

    I had the same problem and built the hearthpad high enough so the exh system cleared the baseboard heat. I went with a 45 then straight through the...
    Post by: rona, Feb 18, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  13. rona
    Post

    Replacing temperature probe

    Go to any hardware store or WalMart very cheap.
    Post by: rona, Feb 18, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  14. rona
    Post

    Harman Service for Pellet Stove Problem

    This was about the time Harman was being bought out by the outfit that owns Quadrafire and according to the powers that be I was lost in the...
    Post by: rona, Feb 9, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  15. rona
    Post

    Harman Service for Pellet Stove Problem

    it happened It happened approx 4 years ago and if it was against the law everybody was pretty quiet about it including the state Harman rep. I...
    Post by: rona, Feb 8, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  16. rona
    Post

    Harman Service for Pellet Stove Problem

    Not picking on one dealer but am curious about something. If you bought a stove from a dealer and after a couple months he dies and the store...
    Post by: rona, Feb 7, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  17. rona
    Post

    how do I get my st. croix scf-50 running optimally

    Your furnace is rated at 50,000 btu on a good day. For a very small house it will work but I've seen it come up short many times. As been said...
    Post by: rona, Jan 25, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  18. rona
    Post

    who runs their stoves when they aren't home?

    These stoves are meant to run 24/7 -- mine starts in Oct and other then cleaning it is on 24/7 using a thermostat house is always 70 degrees. You...
    Post by: rona, Jan 13, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  19. rona
    Post

    Too many moving parts on these machines.

    They can feel smooth at a low rpm such as spinning by hand but it is a common problem on Bixbys and when you spin by hand they seem fine but put...
    Post by: rona, Jan 11, 2013 in forum: The Pellet Mill - Pellet and Multifuel Stoves
  20. rona
    Post

    I think it's time for a cleaning

    Try googling your brand and model number stove and I bet you will find a parts source.
    Post by: rona, Dec 30, 2012 in forum: The Pellet Mill - Pellet and Multifuel Stoves
Showing results 1 to 20 of 198 Next >
Search Again
Page 1 of 10