Welcome fellow Mainer and Harman owner!
This is a Great site and the Harman will keep you warm.
Was a bit hesitant using the RTV on the bare metal flange. Did not want to have to scrape, pry etc. Also wanted to be able to start the stove...
We didn't like the higher price of the P61/install but the stove HAS paid for itself!!
Good luck with install and enjoy!!
Decided to fabricate a high temp gasket per this video:
I did go with his 2 layer approach.(a bit thick though) Wanted a reusable gasket and...
As stated above, I open the door while running and knock that ash into ash pan.
Usually shut stove down to scrape "carbon" buildup from burn pot.
Chose the Harman after 2 months of shopping and talking to both Harman and Englander owners.
Liked the ash pan and 70 lb hopper of the...
We have a P61 in the living room (original stove) and added an Englander 25-pdvc (basement)
Both stoves heat well.
I like the large ash...
Damp paper towel, ash and cool glass here
I extended ours because the space between the back of stove and wall was quite cool. (coiled up sensor and insulation issues)
Before the extension...
I would hope that if all of us purchased only what we needed, then we should be all set.
There was a shortage last Jan-Feb. Never ending cold.........
Last 2 mornings have been in the low 30's. 33 this morning. Jackman hit 18 yesterday and a couple ski areas were making snow! (Testing new equipment)...
The Pellet Warehouse in Jay 645-3064 has MWP, Crabbe out of New Brunswick and possibly LaCrete. Steve Barker is great to work with and
as far as I...
Why heat the air with the stove then throw it outside???
We have the same thing happening. Have not posted anything about it. Have not had any issues but still doesn't look right.
The 2" back you are...
Western Maine near Sunday River
Small Cape: P61 1st floor (7 years) Englander 25-PDVC Basement (2nd year)
4 tons of MWP in basement, will have to...
We have a P61 corner install. Not quite straight out but has one 45 degree then out the wall with no rise.
The dealer installed it. As...
I have the same stove/same issue. Have ordered new triacs. I will post after I replace the triac with results. Can you check igniter with a meter?...
Had same issue.(2008 install) Built a raised pad.
I had to go with a raised pad as well so as to keep exhaust above the hot water baseboard.
Link to my post in 2008:...
Thanks for replies! Spent some time on the phone with Tech from Englander. Ignitor is fine. So took a close look at control board. Looks like the...
Finished moving 4 tons here too. Good exercise, huh?
Get the MWP from Pellet Warehouse?
We will have to get another 1-2 more tons. Added 2nd stove...
Yup did a "Test Burn" after complete cleaning.
51 and raining. Jaymaine, you live in Jay?
I work at Verso.
Ignitor measures 49 ohms. No glow and no start.
Supply volts are 120.
Power to ignitor from relay or transistor?
Just had 4 tons of MWP delivered. $229/ton plus $10 delivery fee.
Pellet Warehouse, North Jay
I do not worry about the ash line. Varies with pellets. We clean the burn pot as needed.
When we purchased the P61 in 2008, my understanding...
A link to the pad I made for a corner install. (2008)
Final picture of...
Thanks for your post!
We picked up a used one and installed it in the basement.
Ours was in mode "A" when we got it. Now in mode "C" Keeping basement...
Looking at ours right now the top of the flame is between the heat exchanger and top of the fire bricks.
This has been the norm when stove is ramping...
Separate names with a comma.