Separate names with a comma.
For most people a phone call to have a qualified technician work on the stove would be a wiser/safer call.
Thanks for reminder!!
I have had a few upper auger issues too.
Here is what I have found and done to address problem:
1. A number of times the stove shut down due...
The only things I can think of:
-Did you hit the ESP probe while cleaning? Located in the exhaust pipe and very delicate
-Did you remove the small...
You should be able to go close to a month. Sounds like the stove and pellets are getting along!
I did a complete cleaning also on...
If not stove will run in Low Heat mode. Forgot about that :(
Check this link out. Verify heat mode. Should be "C"
had similar situation with baseboard. Made my own pad. It is raised so as to clear baseboard.
We are heating 1530 sq ft- 2 floors and...
We use about 257 gal/year for hot water. 40 gal BoilerMate...
About $75/month with oil at $3.50/gal
Here ya go. Taken from a post on this forum. Need that stove running warmer for Polar Vortex!!
On ours (Just checked it), after releasing blower...
Just did a quick calc:
For us 6 tons @ $235/ton=$1410 vs 675 gal@ $3/gal= $2025 reduction still shows us saving.
Yup leave at 4
Cleaning burnpot ash (as needed thru day)--do while running scrape into ash pan shut the door
Cleaning carbon-like build...
We are on our 2nd control board (Harman P61) and have noticed this.
The temperatures on the dial are NOT very accurate. We use a digital...
I was able to trade a wood stove for an Englander last Fall (2nd stove). Installed in basement. Works great easily keeping the basement warm....
The burn in our dealer recommended:
Run stove till you have a good flame then shut it down. Do 4-5 times.
Cannot remember how bad the smell was....
I changed ours a few years back.
Ours is a corner install and I didn't pull it out to give me the room I needed to work. :(
The hardest part of...
Which APC model do you have? Pure Sine Wave?
Congrats on the new stove!
At the minimum, you need to have "True Sine Wave" output to your stove. (Inverters or generators)
I tried a cheap 12v...
Here is what I did. Wanted a reusable gasket!
Also like the rope idea. Maybe us RTV with rope to form.
Here is the link to the gasket I made....
Welcome fellow Mainer and Harman owner!
This is a Great site and the Harman will keep you warm.
Was a bit hesitant using the RTV on the bare metal flange. Did not want to have to scrape, pry etc. Also wanted to be able to start the stove...
We didn't like the higher price of the P61/install but the stove HAS paid for itself!!
Good luck with install and enjoy!!
Decided to fabricate a high temp gasket per this video:
I did go with his 2 layer approach.(a bit thick though) Wanted a reusable gasket...
As stated above, I open the door while running and knock that ash into ash pan.
Usually shut stove down to scrape "carbon" buildup from burn pot....
Chose the Harman after 2 months of shopping and talking to both Harman and Englander owners.
Liked the ash pan and 70 lb hopper of...
We have a P61 in the living room (original stove) and added an Englander 25-pdvc (basement)
Both stoves heat well.
I like the large...
Damp paper towel, ash and cool glass here
I extended ours because the space between the back of stove and wall was quite cool. (coiled up sensor and insulation issues)
Before the extension...
I would hope that if all of us purchased only what we needed, then we should be all set.
There was a shortage last Jan-Feb. Never ending...