Planning an update for next year

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

meebers

New Member
Mar 15, 2012
5
Central Florida
Bought this house new 12 yrs ago with a builder installed Majestic UVC36, NG Non-vented fireplace. The heater works great but there has always been an annoying smell when lit. It sort of smells "sour" and we have been putting up with it since new. Filters cleaned every year per the mfg instructions, logs carefully placed as instructed etc. Last year, I even called the local gas company to come and check it out, his inspection revealed nothing wrong, took sniffer/meter readings, all were well within specks. We have a Co-2 monitor installed, never has alarmed, but I have always had to remove a normal smoke detector in that room to keep the whole house from alarming. After 11 years, changed all the smoke detectors to an "improved version", and within a minute, the SD will alarm. So...I think I would like to change this insert out to a vented version, this summer, hopefully some will be on sale???. The vent is the biggest question to muddle through. On top of this heater is a cove that is the same width as the stove and about 2 feet high, 2 feet deep. Hate to have to run a vent up through the middle of this (to the roof, approx 15') as the wife is giving me the "eye" about it, can run to an outside wall, on a porch and either leave it there??or elbow it up through a 4 ft wide soffit to the roof. In either case, what type vent would I use, double inner/outer (one for input air and one for exhaust)??. Just in the planning stages right now, appreciate any thoughts. ;lol
 
Direct vent (inner/outer tube) can run through the wall, either straight out the back of the stove so no pipe is visible or up out the top and then through the wall (or ceiling)... it depends on the model.

If you vent through the wall there are required clearances from the vent to soffit, windows, etc. This document gives the required clearances for Simpson Duravent pipe.
 
Tx Fan Man. Finally got thru the document and understand most of it. One option is to come up with the vent and make an immediate 90 degree turn to go thru an outside wall. This wall is on a covered porch where the soffit is 48". Think this might then vent up into the attic and exit thru roof vents. Does that sound like workable idea? or would it be best to do a 90 and take it up thru the soffit and then the roof. Forgot to add, behind the FP is a bathroom.
 

Attachments

  • fp1a.JPG
    fp1a.JPG
    35.3 KB · Views: 184
  • fp2a.JPG
    fp2a.JPG
    64.5 KB · Views: 178
Top vented stoves may have a minimum amount of vertical pipe before the first elbow. Mine needs at least 24", and that's what I used as any move would put the vent on the outside too close to the soffit. If I understand correctly you want to go through the exterior wall, then back in through the soffit and out the roof? Seems a lot of work.
 
Bottom line? Choose a unit that can be vented in the manner you want, then
see what the clearances and allowable configurations are for venting it.
Looking at the venting clearance for a specific vent manufacturer may not tell
you the clearances for the venting for that particular unit.
 
Top vented stoves may have a minimum amount of vertical pipe before the first elbow. Mine needs at least 24", and that's what I used as any move would put the vent on the outside too close to the soffit. If I understand correctly you want to go through the exterior wall, then back in through the soffit and out the roof? Seems a lot of work.

Thats the question, it seems like I do not have any really good choices that are straight forward. In ref to the picture, you can see that the other option is to go thru the center of the opening above the FP, wife is not supporting that idea :-(

Daksy: I called a local gas/fireplace guy this morning, awaiting his thoughts, but yes will have to choose a compatible FP to allow the vent install that is up to code and is pleasing to the eye.

Question #2. I assuming a couple of things here, vented vrs non vented should not allow any odor etc in the main room? (the main reason I am changing) IF I get a blower for the FP that does not change?? The blower uses air from heat exchanger or sealed shell around the main FP. Sorry lost here.

This may see silly ?? since I am in Central Florida, but there are times that we unfortunately go below freezing here. The present fireplace was able to keep up with the temp without any help from the heat pump, otherwise would not be looking to change. ;-) Something I called "Palmsicle"
 

Attachments

  • Palm Sicles.jpg
    Palm Sicles.jpg
    101.3 KB · Views: 174
Thats the question, it seems like I do not have any really good choices that are straight forward. In ref to the picture, you can see that the other option is to go thru the center of the opening above the FP, wife is not supporting that idea :-(

If you can talk her into going thru the center of that alcove above the current unit, You can explain to her that after the vent is installed, it can be boxed in & she'll still have MOST of that space for her stuff. It'll just be two smaller
openings. Generally speaking, you will lose approximately 12" x 12" x the height...

Daksy: I called a local gas/fireplace guy this morning, awaiting his thoughts, but yes will have to choose a compatible FP to allow the vent install that is up to code and is pleasing to the eye.

Looking at the 2nd of your pics, that light will have to be re-situated & again, you'll have a roughly 12 x 12 structure extending into the covered porch...

Question #2. I assuming a couple of things here, vented vrs non vented should not allow any odor etc in the main room? (the main reason I am changing) IF I get a blower for the FP that does not change?? The blower uses air from heat exchanger or sealed shell around the main FP. Sorry lost here.

You will get odors from the new unit for maybe the first 4 hours as the paints, oils & adhesives used by the manufacturer cure due to the heat. There may also be some smoke from that curing...Once the curing is done there will not be any smells as long as the new unit is kept free from dust. Most of the blowers will draw cooler air from the floor in front of the fireplace & push it up thru a cavity in the rear of the unit & across a heat exchanger on top to get warmed air out into the room. There will not be any smells, as long as the glass is securely fastened. Direct Vent units have sealed combustion chambers. Over summer months, dust will settle in the blower cavity & on the heat exchanger. If those areas are not cleaned at the beginning of the next heating season, the dust will BURN off & you will smell that burn off for the first half hour or so...

This may see silly ?? since I am in Central Florida, but there are times that we unfortunately go below freezing here. The present fireplace was able to keep up with the temp without any help from the heat pump, otherwise would not be looking to change. ;-) Something I called "Palmsicle"
 
The fireplace/Gas guy was here this morning. After some measurements, said that by the time you add a vertical stack to the fireplace then go horizontal thru the wall you would have less than 36" (code) to the soffit. Also could not just exit on the porch because it is considered a closed space living area. It is screened but his past experience was that eventually people want to enclose the screen/porch and therefore (code) will not allow it. Only solution is to go straight up thru the top/attic/roof with about an 18" exposed stack on the roof. Also did not realize that the firebox is larger than the exposed front area and therefore, all the tile will have to be removed, restructure with new tile, and structure around the 6" stack. (approximately a 10" square area) etc. One more note is that an electrical outlet will have to be installed to run the ignition & blower. How do you spell "money pit"?:p. He is looking at compatible units and will be back in contact.
 
Status
Not open for further replies.