18" or 20" Bar for 562XP for firewood?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

scooby074

Feeling the Heat
Jan 7, 2011
423
Nova Scotia
Im thinking of upgrading the factory Husquvarna 18" bar on my 562XP to a Powermatch 20"with a Stihl chain. I cut 95% of my firewood off the pile. Typical diameter of my current batch is probably about 10" on average

Im going to get a new chain regardless if I stay with the 18 or go to the 20 because I hate Oregon's chains and usually only run Stihl.

The factory bar that came with my saw is a bit of a POS. I call it the Pinchmaster 9000. ;) . Its a non-replaceable rollertip that is held together with very tiny rivets. The slightest pinch and the chain grove closes up. Sometimes so tight that I have to pull the chain and re-spread the groove with a screwdriver. Honestly its one of the worst bars Ive ever used when it comes to that. Frankly I expected better. I think is's an Oregon bar but I dont know which model. I thought the pro-saws came with Husquvarna branded Powermatch's? Ive never had a PowerMatch jam up like this thing. Ill snap a pic tomorrow of the bar.

So 18" or 20"????
 
Sounds like one of Oregon's cheaper laminated bars.Oregon makes all the other OEM branded bars,except for Stihl.Not sure how they're made today,but the 20" factory laminated bar on my 62cc Super 380 finally gave out in September after 12 1/2 yrs,100+ cords & lots of abuse.(Non-replaceable sprocket nose finally failed).I certainly cant complain about its longevity.

Maybe they're lower quality now,wouldnt surprise me none.

PowerMatch is a good choice,first one I bought was in 1994 for a McCulloch Pro Mac 610.Bought 2 more different lengths since then.I think they all say 'Power Match Plus' now,the newest one from last summer does anyway.
 
  • Like
Reactions: smokinj
Go big or stay home. Ain't much difference from 18 to 20" anyhow!!!! If'n you've got a pair, you can handle it!!!
 
  • Like
Reactions: smokinj
So 18" or 20"????
Typical diameter is 10" on average

For your use
I vote 18"

Agree, Husqy don't put good bars on their saws.
 
  • Like
Reactions: smokinj
I'm curious as to what your current bar is. There should be information (part no., pitch, gauge, DL, et al.) stamped on the bar near the mounting slot .
 
  • Like
Reactions: smokinj
So 18" or 20"????
Typical diameter is 10" on average

For your use
I vote 18"

+1
You won't cut that log any faster, you'll have more weight to lug around, and I can't see a longer bar being any safer.

I run a 16" bar on my 359 due to being in trees that average 12-14". After having run an 18" bar for years, I am quite happy with the 16".
 
  • Like
Reactions: smokinj
Sounds like one of Oregon's cheaper laminated bars.Oregon makes all the other OEM branded bars,except for Stihl.Not sure how they're made today,but the 20" factory laminated bar on my 62cc Super 380 finally gave out in September after 12 1/2 yrs,100+ cords & lots of abuse.(Non-replaceable sprocket nose finally failed).I certainly cant complain about its longevity.

Maybe they're lower quality now,wouldnt surprise me none.

PowerMatch is a good choice,first one I bought was in 1994 for a McCulloch Pro Mac 610.Bought 2 more different lengths since then.I think they all say 'Power Match Plus' now,the newest one from last summer does anyway.


100 cords you sissy. :p Oh and make it a 32 full skipper! ;)
 
  • Like
Reactions: Thistle
Get a20" techlite bar . You'll like it .

I wish!! Those top of the line bars, like the Techlite, Gannons, Sugihara's and things like that arent even on the shelf here!! Then there's the cost.. If its $100 at Baileys, it'd be $150 or more here. A little too rich for me.

Ive always bought PowerMatch's and have had very good luck with them... Plus all that's available locally is the PM and Stihl's.

Im leaning more towards the 20 for the added reach, I'm 6'1 so less stooping is good.
 
Can't blame you for balking at cost . I just did the same on a 28" ES light . $147.00 ! Bought an ES ,then ordered a 24" Sugihara .
 
  • Like
Reactions: smokinj
Can't blame you for balking at cost . I just did the same on a 28" ES light . $147.00 ! Bought an ES ,then ordered a 24" Sugihara .


I love the es the last one I got was a 32 for 79.99 bucks. Now double that for the light and I am out.
 
  • Like
Reactions: Nixon
I love the es the last one I got was a 32 for 79.99 bucks. Now double that for the light and I am out.
Yep , ES bars are as good as there are for the bucks . ES lights..... Not so much .
 
  • Like
Reactions: smokinj
100 cords you sissy. :p Oh and make it a 32 full skipper! ;)


;lol Not on that Super 380,thank you. Does pull a 24 skip quite nicely however. Pretty nose heavy with it though,powerhead is only 12.5 lbs.
 
  • Like
Reactions: smokinj
Went to the Stihl dealer today to get a 20" PM ... No dice. Have to order the bar . End of next week if I order, so I told him to hold it until I check other dealers. He doesnt have anything over 16!! Says they might have sold 5 20" in 10 years. Mostly its 14 and 16" he sells..Well its all he stocks!

On the chain, He didnt have any 20" loops in stock, so that would be an order too.

So I figured I'd upgrade my stock 18" Oregon chain to my favorite RSC. After spending about 30 minutes there while they tried to figure out sizes (even though I told them) and counting links, he says that'd he'd have to brake a stock 60 tooth chain and add 8 teeth in order to me a chain, AND charge me for 2 loops because he had no bulk chain!!! Needless to say I left without the chain.

I'll either find some 18" 35RSC 68 on a shelf or order one in. Im not too interested im paying for full extra loops just to cut them up. Not a real good day!
 
Went to the Stihl dealer today to get a 20" PM ... No dice. Have to order the bar . End of next week if I order, so I told him to hold it until I check other dealers. He doesnt have anything over 16!! Says they might have sold 5 20" in 10 years. Mostly its 14 and 16" he sells..Well its all he stocks!

On the chain, He didnt have any 20" loops in stock, so that would be an order too.

So I figured I'd upgrade my stock 18" Oregon chain to my favorite RSC. After spending about 30 minutes there while they tried to figure out sizes (even though I told them) and counting links, he says that'd he'd have to brake a stock 60 tooth chain and add 8 teeth in order to me a chain, AND charge me for 2 loops because he had no bulk chain!!! Needless to say I left without the chain.

I'll either find some 18" 35RSC 68 on a shelf or order one in. Im not too interested im paying for full extra loops just to cut them up. Not a real good day!

You are looking for a .058 gauge bar and chain, right? Did your dealer have 20" bars and chain in .050 gauge? If you're adding a 20" bar and chain(s) to your saw, a switch to .050 gauge won't be a problem, unless .058 is more popular at dealers in your region.
 
he had nothing in 20"s. no bars or (Stihl) chains. Nothing in 18 either.
 
I cut 95% of my firewood off the pile. Typical diameter of my current batch is probably about 10" on average

On a log pile I say a shorter bar is safer. If you don't need the length then all it is doing is sticking out the back side of the log you're cutting & getting into something you don't mean to be cutting (another log, ground...).
Vote for a 16" bar & add a 20" if/when you need it.
BTW, I find felling wedges very helpful for stopping pinches when bucking from a pile. Everything I scrounge is on the ground so bucking is all I've used my wedges for. Not sure if they'd be any use on logs under 10-12" though.
Oh, and your Stihl dealer sucks man :rolleyes:
 
Why not order it from Baileys?

16 inch from the pile for reasons others have stated. I also have a 20 inch for reach, could really do with the next size up to save my back.
 
Im thinking of upgrading the factory Husquvarna 18" bar on my 562XP to a Powermatch 20"with a Stihl chain. I cut 95% of my firewood off the pile. Typical diameter of my current batch is probably about 10" on average

Im going to get a new chain regardless if I stay with the 18 or go to the 20 because I hate Oregon's chains and usually only run Stihl.

The factory bar that came with my saw is a bit of a POS. I call it the Pinchmaster 9000. ;) . Its a non-replaceable rollertip that is held together with very tiny rivets. The slightest pinch and the chain grove closes up. Sometimes so tight that I have to pull the chain and re-spread the groove with a screwdriver. Honestly its one of the worst bars Ive ever used when it comes to that. Frankly I expected better. I think is's an Oregon bar but I dont know which model. I thought the pro-saws came with Husquvarna branded Powermatch's? Ive never had a PowerMatch jam up like this thing. Ill snap a pic tomorrow of the bar.

So 18" or 20"????

Definitely 18"

You wouldn't want to push that poor little machine too hard.
 
  • Like
Reactions: smokinj
Why not order it from Baileys?

16 inch from the pile for reasons others have stated. I also have a 20 inch for reach, could really do with the next size up to save my back.

Because Baileys shipping to canada is foolish money. I called them once to order something (small) , I think it was a speed feed trimmer head, and shipping was $30. Then there is brokerage at the border because they wont use USPS, which adds another $30.

Now if they'd use USPS or get a Canadian warehouse, they'd probably get 90% of my business when it comes to chainsaw/small engine stuff.
 
  • Like
Reactions: HittinSteel
On a log pile I say a shorter bar is safer. If you don't need the length then all it is doing is sticking out the back side of the log you're cutting & getting into something you don't mean to be cutting (another log, ground...).
Vote for a 16" bar & add a 20" if/when you need it.
BTW, I find felling wedges very helpful for stopping pinches when bucking from a pile. Everything I scrounge is on the ground so bucking is all I've used my wedges for. Not sure if they'd be any use on logs under 10-12" though.
Oh, and your Stihl dealer sucks man :rolleyes:

Indeed he does.

They used to be a full service saw shop, complete with bulk chain and everything, but there is just no call for that now. He wasnt the only saw shop in town either, there were several others that have since closed up shop. There used to be a lot of manual forestry, but much of it has been replaced with harvesters, so there is no real call anymore for anything more than typical homeowner stuff.

I know of 2 old school saw shops left, but they are an hour away in opposite directions. They are Husky /Oregon dealers though, which means I could get my bar, but not the RSC chain I want.
 
Definitely 18"

You wouldn't want to push that poor little machine too hard.

I think the 562 wont have a problem. It pulls the 18 without flinching. Plus, given that the wood itself is only 10", there should be no real difference in performance. Maybe if I had it buried in a huge log or something I could see it.

Im not worried about cutting into the next log on the pile anyways, im usually cutting in the tip area so Im not more than an inch or two out the backside of the log Im cutting.
 
Status
Not open for further replies.