Crack Firebrick a Problem?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

jimmieguns

Member
Dec 10, 2012
219
Long Island, NY
Hello Friends!

Can you please share with me if this cracked brick is a danger or burning problem-ie, excess draft,lost heat etc? Many Thanks

crackedbrick.jpg
 
Unfortunately, it's likely a sign of whats behind the scenes. I would guess there are other problems behind that panel. What model do you have?
 
Unfortunately, it's likely a sign of whats behind the scenes. I would guess there are other problems behind that panel. What model do you have?

It is a vermont casting 0044.......my chimney sweep said he didnt think its a problem--actually shrugged it off- but I respect you guys here more!

Thanks
 
As long as it stays intact it should be fine
 
I say a problem. Reason being fire going up under that cast piece above it instead of up the flue.
 
As long as it stays intact it should be fine

That exactly what my chimney chap said, but i trust you guys more here! thanks...should i try to replace myself without removing unit? like just try to pull out and "shove" in there? is that even possible? i know brick stores near me must sell firebrick. Thanks
 
I say a problem. Reason being fire going up under that cast piece above it instead of up the flue.

Thats what I was thinking, but what harm can be done if that is so? start a house fire? lost heat? can I live with it?
 
At the very least stuff the hole full of furnace cement or refractory cement. Both available at Home Depot.
 
At the very least stuff the hole full of furnace cement or refractory cement. Both available at Home Depot.

Great Idea !!! Many thanks...just use as directed or use com
cccc5924-7957-4473-b097-3ee5ab976c82_300.jpg
mon sense and "fill her up tight" ? thiis looks perfect
 
Clean the crud out from behind the brick first and shove it back in place. Burn a low kindling fire after you put the stuff in there to dry it out and set it.
 
  • Like
Reactions: jimmieguns
Clean the crud out from behind the brick first and shove it back in place. Burn a low kindling fire after you put the stuff in there to dry it out and set it.

Ok, so its safe to pull the cracked(right side one) out completely? then clean like you said,shove in and cement? thanks!
 
Beats the hell out of burning in the thing like it is. >> Of course a brick is like three bucks at my stove store. But that looks like a long strip of refractory. A Vermont Castings specialty. Chit ya can't find anywhere.
 
Beats the hell out of burning in the thing like it is. >> Of course a brick is like three bucks at my stove store. But that looks like a long strip of refractory. A Vermont Castings specialty. Chit ya can't find anywhere.

Yeah, you aint chittin me! !!! better to go with the furnace cement like you said , I think.
 
Beats the hell out of burning in the thing like it is. >> Of course a brick is like three bucks at my stove store. But that looks like a long strip of refractory. A Vermont Castings specialty. Chit ya can't find anywhere.

just found some related ino-which i suspected!

Damaged or missing firebricks inside the stove will allow the stove to cool excessively. You need to have a hot firebox in order to achieve complete combustion. Replace missing or damaged firebricks.

Replace damaged or missing firebricks. The firebricks insulate the firebox, which needs to be maintained at a high temperature in order to fully-combust the fuel. If the firebox is less than adequately insulated, the combustion temperaure decreases leading to an increase in smoke, and lower efficiency.
 
Clean the crud out from behind the brick first and shove it back in place. Burn a low kindling fire after you put the stuff in there to dry it out and set it.

Good morning BrotherBart-- gonna fiv my broken firebrick today if I get the chance-question, you said to burn a low grade kindling fire afterward--- how low is low please? and for how long should do you think I should let it burn? I usually start my fire out with wads of newspaper and kindling. This gets a fierce initial flame inside the insert. Is that TOO much for the curing i am trying to accomplish?

THANKS!

J
 
Temperature is more important than amount of flame. Just burn some kindling for thirty minutes or so and that should cook the moisture out of the furnace cement fine.
 
Temperature is more important than amount of flame. Just burn some kindling for thirty minutes or so and that should cook the moisture out of the furnace cement fine.

OK, THANKS BUT CAN i GO AHEAD RIGHT INTO A REGULAR FIRE RIGHT AFTERWARD? iT'S COLD HERE oops caps sorry--its cold here and wanted to run the insert most of the day -but also wanted to address the problem...whats best to do? thanks!
 
Yep. Let'er rip.
 
Give it a half hour of low heat and then burn like ya always do. You do the low burn to dry it so that you don't have to wait twenty four hours.
 
Give it a half hour of low heat and then burn like ya always do. You do the low burn to dry it so that you don't have to wait twenty four hours.
ok Thanks-- another question please-- i am replacing the door gaskets and i think they call for 5/16 but i can only find 3/8 inch in my area. its a TIGHT TIGHT squeeze but i think i could get it in.. IS that safe to try or best to wait and keep looking for the 5/16 THANKS!
 
Get the 5/16". Force the doors and you are gonna break something.
 
Give it a half hour of low heat and then burn like ya always do. You do the low burn to dry it so that you don't have to wait twenty four hours.

Hello My Brother Bart.....many many thanks for all your wisdom ,support and advice---you are SPOT-ON! on all your rec's....sealed my cracked firebrick, ordered th correct gaskets and have gotten bettter overall temps,,,,,,,,much less "leakage thru broken bricks" and better temps,,,,,,,,, I am just trying to be realistic and figure if my old VC 0044 can REALLY heat a 2000 sq ft home with poor insulation and vaulted ceilings-----maybe I am asking for too much-huh? it takes about 2-3 hours to get to 500-600 degrees internal box temp(thru glass).. ANY IDEAS? Please!
 
It would be very, very, hard for this unit to heat that house without some help from another heat source.
 
It would be very, very, hard for this unit to heat that house without some help from another heat source.
That's what i was thinking ...why do you say that? Just curious....it's age or because its an insert ?
 
Status
Not open for further replies.