Skidding tongs?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
I need to get a some skidding tongs. Can I get someone's recommondarion on what makes a good set. I get a grapple load of logs every year would like something better and quicker than a chain. I am looking at these.

https://www.baileysonline.com/search.asp?catid=1793&skw=SKIDDING TONGS

IMGP3435.JPG

These are log dogs. They are used in the beach combing industry here on the west coast.

IMGP3575.JPGIMGP2978.JPG

To set them in the log, you just drive them in with a five lb. hammer. To get them out, you just hit them on side once or twice and they come out.

IMGP2980.JPGIMGP2982.JPGIMGP1413.JPGIMGP1417.JPG

If you think these might work for what you are doing, I would be happy to go to the local logging supply and mail it to you. I am guessing but I think they are worth about $3.00 each plus probably $10 postage. I can find out more accurate pricing if you are interested.
 
Those are fantastic! You wouldn't think they would hold so well, but I use the same principle with my machete to pick up rounds and splits without bending over.
 
Hobbyheater Thats a awsome splitter who made it or is it homemade??
 
Hobby, can they pull whole logs? It sounds too good to be true.

IMGP3517.JPG

If this log was on flat ground with no potential for hang ups I would use the dog.

IMGP3520.JPG

Again I have choked the log for a tough pull.

IMGP3571.JPG

Used a roll to get a log out of a hole.

IMGP3574.JPG

This log gave more than 1/2 cord of wood. On flat ground I would not have trusted the dog to hold.

I was right on the price of the log dog at $3.00, but behind the times on the postage $ 24.00 not $10.00.
I have traced back to where they are made and they are only sold on the West Coast; Alaska , Washington State and BC.
 

Attachments

  • IMGP3517.JPG
    IMGP3517.JPG
    233.3 KB · Views: 229
  • IMGP3519.JPG
    IMGP3519.JPG
    243.1 KB · Views: 215
  • IMGP3520.JPG
    IMGP3520.JPG
    265.4 KB · Views: 230
The splitter was 1 of 24 made in the early 80s by the Wilson brothers at Fruitville, BC. It was known as the Wilson Beaver Chomper.
Nice splitter Allan, can you show a picture of the winch setup ? It sure looks like a back saver on those big rounds. I don't hear about Fruitvale very often , went to junior high there in that metropolis in the 60's.
 
View attachment 90933

I added the block for a fairlead in the fall of 2011. It works much better than the rollers that came with the winch.

View attachment 90934

View attachment 90935


View attachment 90936


View attachment 90937

The four way wedge is forged and is just as sharp today as it was 30 years ago.
Thanks for the pictures Allan, was the splitter born with a winch or did you design this setup? Can the splitter engine charge the battery or will a charged battery last as long as you feel like working?K
 
Thanks for the pictures Allan, was the splitter born with a winch or did you design this setup? Can the splitter engine charge the battery or will a charged battery last as long as you feel like working?K

The winch was my add on . The 13 HP Honda has a good charging system.
 
Status
Not open for further replies.