First 1 Ton Cleaning - XXV

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.
A quick question from a wood burner. Do the temps in the flue of a pellet stove ever reach a point where they could cause a chimney fire? I was just curious, after viewing this thread. Maybe a stupid question, but I don't know anything about these pellet stoves. Forgive me.
No question is a dumb question in my book.
Yes. Typically pellet soves burn much cleaner than other type of wood burning appliances and a properly working pellet stove will create very little creosote. Startup and low burns can create the sote but it is usually burned off when the stove reaches higher temps. However prolonged low temp burns and/or poor stove maintenance could result in creosote issues and lead to venting fire.
 
Seen a wood stove chimney fire first hand. As they say in these parts "Wicked".
 
Great post love all the pics and detail. Nice set up, beautiful stove, if it were me I would paint the stove pipe black, just me I think it would look better.
 
Great post love all the pics and detail. Nice set up, beautiful stove, if it were me I would paint the stove pipe black, just me I think it would look better.
I think your right on. Absolutely. It's already on the "honey do" list.
 
  • Like
Reactions: will711
Seen a wood stove chimney fire first hand. As they say in these parts "Wicked".

I've had one! Sounds like a rocket taking off. Gets the heart racing a, 911 call fire dept. all better. Helped make the decision to buy a pellet stove easier.
 
Really great thread! Awesome details and pics. Thanks for taking the time to post.
 
I've had one! Sounds like a rocket taking off. Gets the heart racing a, 911 call fire dept. all better. Helped make the decision to buy a pellet stove easier.

Parents house - vent outside my bedroom window. Scared the hell outa me (parents too). Ya just like a rocket, flame to match. Turned out ok though, no damage.
 
"Ahh $hit, That ain't good." lol.
 
Smokey, What do you make of the hard crusty buildup in the upper portion of the venting?
 
good post.....wish all my customers went to this level of detail! keep it up!
 
Fines Box

The fines box is easy to open.
xxv.fines.before.jpg

Got the bulk but decided to vac out the pellets and
get a better look.
xxv.fines.before.2.jpg

Looks ok to me.
xxv.fines.after.jpg

Next. Before and After - Exhaust Path.
 
Smokey, What do you make of the hard crusty buildup in the upper portion of the venting?

Likely ash embedded in the wood burners nightmare or some vent makers apply a liner to their flues that melts and fuses with ash sealing minor flaws in seams.

This is common at the ends of vent runs due to cooler temepratures, a lot of this stuff gets generated when the stove goes through shutdown or bounces between low and high burn mode.

In a short vent system it frequently ends up on the ground or on the critter screen. I remove my critter screen and let it hit the ground during burn season. Because the air flow can get the mess out of the flue before it condenses or precipitates out.

You can also get silicone sealant or lubricant for the joint seals that will fuse with ash.

If it is black consider it a creosote and whatever mixture and brush it out or otherwise get rid of it. Warm water on a old towel works well, you just have to watch out for the mess at the other end (stove end and floor) so you don't ruin things instead of cleaning things.

I see a nice light gray color for most of what was in your flue.

I plan on pulling the term cap off mine this afternoon and removing any ash, I don't want anything to be able to get between me keeping the place warm the next few days because of an unscheduled shut down.
 
Before and After - Exhaust Path- Final Rear Shot.


xxv.exhaust.rear.before.jpgxxv.exhaust.rear.after.jpg

Forgot to grab a closeup of this flue area are but you can see it just about clean in the
second pic.
xxv.comb.box.before.jpgxxv.comb.behind.after.jpg

Flue Intake.
xxv.exhaust.before.jpgxxv.exhaust.after.jpg

While were here...
A before shot of the convection fan. I am really surprised
it's not full of dog hair.
xxv.convection.before.jpg

Last shot before the back panels go on.

xxv.back.after.jpg


Next : Regular Maintenance - 2 Week Run.

 
Is the fines box on the left or right side of the stove? I tore apart the left side where the blower is but did not see the fines box. So I assume it's on the right side of the stove.
Yes. Take off the right panel (facing the stove) look for a big wing nut.
 
Said it before Great Post ! Maybe the Mods can put it all together and make a sticky out of it.
 
Likely ash embedded in the wood burners nightmare or some vent makers apply a liner to their flues that melts and fuses with ash sealing minor flaws in seams.

This is common at the ends of vent runs due to cooler temepratures, a lot of this stuff gets generated when the stove goes through shutdown or bounces between low and high burn mode.

In a short vent system it frequently ends up on the ground or on the critter screen. I remove my critter screen and let it hit the ground during burn season. Because the air flow can get the mess out of the flue before it condenses or precipitates out.

You can also get silicone sealant or lubricant for the joint seals that will fuse with ash.

If it is black consider it a creosote and whatever mixture and brush it out or otherwise get rid of it. Warm water on a old towel works well, you just have to watch out for the mess at the other end (stove end and floor) so you don't ruin things instead of cleaning things.

I see a nice light gray color for most of what was in your flue.

I plan on pulling the term cap off mine this afternoon and removing any ash, I don't want anything to be able to get between me keeping the place warm the next few days because of an unscheduled shut down.

I think your dead on with the "mix", fits my burn pattern. Not black though like sote. In any event I don't like it... Easy to remove the pipes and make 'em shiny again. Good tips.

Supposed to have a pretty good cold snap in the coming days. Get 'Er clean, stay warm!
 
Pretty intense monthly cleaning, about what I plan to do for my end of season cleaning after 5 tons. (I do fines / brush everything inside / quick vacuuming / empty ash monthly)

Not sure if XXV does, but did you get the igniter clean out? Mine usually has a handful of ash debri in there.

Also right above the window on the inside, mine gets a lot of ash build up there.

I was going to do a full annual cleaning guide, but now I don't have too =) Nice job.
 
Said it before Great Post ! Maybe the Mods can put it all together and make a sticky out of it.
Thanks man. I wouldn't object.
Maybe next round I can spend more time and expand this with pics showing more doing , like a how to. My other half wasn't around to help me out. Or maybe she just didn't want to be cold? Hmm...
 
  • Like
Reactions: will711
Pretty intense monthly cleaning, about what I plan to do for my end of season cleaning after 5 tons. (I do fines / brush everything inside / quick vacuuming / empty ash monthly)

Not sure if XXV does, but did you get the igniter clean out? Mine usually has a handful of ash debri in there.

Also right above the window on the inside, mine gets a lot of ash build up there.

I was going to do a full annual cleaning guide, but now I don't have too =) Nice job.

Thanks!

I did not have any idea what to expect so I wanted to investigate everything. My first ton ever.

You can wait for 5 tons? I do not think I would attempt that. Based on what I discovered there are some things I could probably let go longer. I would be scared to go that long but I am still inexperienced so better safe than sorry for me.

Ignitor pics are coming soon!
 
I'm at 4 tons now, hoping 5 is enough for the season. Like I said I do a quick monthly, but I don't think I will need to brush flue except annually. Result's will vary, but I can see my exhaust on the side of the house, and know it is clear. Likewise, my tee gets very little ash, so chances are my venting is still fine. You hear about people going 2-3 years without a brushing all the time (They pay for it...)
 
Status
Not open for further replies.