Blue flame only on older propane fireplace

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
Status
Not open for further replies.

wickman

New Member
Jan 28, 2013
3
I have a Heatilator GNRC33 in propane and rear vent and standing pilot. It's about 10 years old. When new and for the first 5-6 years it worked great with pretty yellow flames and looked like a real fireplace. After six years or so the flame size started to diminish to a smaller, bluer flame. This year the flame is completely blue. I don't see any ghosting or lifting but just a blue flame. I opened up the glass and blew everything out. I pulled the logs and burner and blew it out. I closed the air shutter on the burner tube a little. It was opened all the way. Nothing has really altered the blue flame. I can try closing the air shutter more but I think it's odd that the fireplace worked fine for many years with the shutter in the full open position. Is there any other possible cause of blue flame?
THX> Eric
 
thats odd!
usually it goes the other way :)

not familiar with that model, is it b-vent or direct vent?

some how more air is mixing with the gas,
or you are getting less gas thru the valve now so the mix is cleaner
 
It's a rear direct vent. And it is very odd. The pilot seems to be working and lighting as it should. I do notice that when i flip the switch the burner portion closest to the pilot comes on first but doesn't travel around the whole burner for a few more moments - say 30 seconds or so. It does light up all the holes eventually but just not immediately.

With propane is it more normal to have to air shutter more open or closed?
 
Well i may have fixed it. I took out the logs and burner again tonight with the intent of another cleaning and closing the air shutter a bit more. I noticed that the gas pipe protruding into the burner pipe (where the air shutter is) has a real tiny hole where the gas flows. The little hole had some white residue in the hole. I took a tooth pick and pushed it slightly into the hole and twisted a bit. It came out pretty dirty. I shut the air shutter a bit more and put everything back together. I now have pretty yellow flames again. I may need to remove that little nipple piece and actually clean it out on the inside and open the air shutter back to the original position. I think cleaning that piece may have done the trick.

THX> Eric
 
That piece with the little hole is the orifice, which controls the gas flow. It's made to a very precise size; be careful cleaning it because it's soft brass and any damage will mess up the gas flow (as you found out).
 
Well i may have fixed it. I took out the logs and burner again tonight with the intent of another cleaning and closing the air shutter a bit more. I noticed that the gas pipe protruding into the burner pipe (where the air shutter is) has a real tiny hole where the gas flows. The little hole had some white residue in the hole. I took a tooth pick and pushed it slightly into the hole and twisted a bit. It came out pretty dirty. I shut the air shutter a bit more and put everything back together. I now have pretty yellow flames again. I may need to remove that little nipple piece and actually clean it out on the inside and open the air shutter back to the original position. I think cleaning that piece may have done the trick.

THX> Eric

You might want to shut er down & pull the orifice. If you had build up around the hole, it came from the gas line behind it. Pull it & run a Q-tip in there...probably be the remains of a spider's nest. Not uncommon in a gas unit...
 
You might want to shut er down & pull the orifice. If you had build up around the hole, it came from the gas line behind it. Pull it & run a Q-tip in there...probably be the remains of a spider's nest. Not uncommon in a gas unit...

frickin spiders... they LOVE to build nests in the burn tube of my grill...
 
Status
Not open for further replies.