Harman p43 ignitor on it’s way out?

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.

D-mac02

Member
Dec 21, 2013
140
New York
hey guys I just deep cleaned my stove and it’s taking forever for the thing to light. Enough to where the pot fills up and I actually either have to take pellets out or light it with a map gas torch. I have an old Ignitor I took out last year and I saved it just in case I had a problem. It took a little long to light too but figured just in case I’ll have a backup. I took and measured the ohms with a meter today and it’s at 62 ohms. Is that good or high? Before anyone asked I cleaned the holes with a screw, cleaned off the Ignitor with a toothbrush, cleaned the fines box and made sure all covers were on tight. Should I get a new ignitor or no? Any other ideas?
 
I would recommend a original Harman igniter. They are lasting a long time now. I hardly ever replace igniters anymore.
 
  • Like
Reactions: bags
Is the ohms a good measurement as to good or not? I've noticed mine taking a good long while to get lit up, sometimes it's really smoking before it catches. I'm at 12 years, and on my second ignitor, so it wouldn't surprise me if it were time.
 
Is the ohms a good measurement as to good or not? I've noticed mine taking a good long while to get lit up, sometimes it's really smoking before it catches. I'm at 12 years, and on my second ignitor, so it wouldn't surprise me if it were time.
i have put in brand new ignitor and at times it takes quite a few minutes to ignite.. 10 minutes or more.
have noticed also that when the burn pot is cleaned,[ like vacuum cleaned], ignition time is lot quicker with no smoke.
could just depend on how much ash the ignitor heat has to blow thru.
 
  • Like
Reactions: glockshooter
Is the ohms a good measurement as to good or not? I've noticed mine taking a good long while to get lit up, sometimes it's really smoking before it catches. I'm at 12 years, and on my second ignitor, so it wouldn't surprise me if it were time.
Ohms is usually a good indicator.people will argue about cartridge heaters,but some designs have multiple heating elements,inside,and possible to loose only part of it,which,as they are connected in parallel,resistance goes up.Easiest way to tell is hook ignitor to 120 volts,should glow red within 2 minutes,and about 85% of the ignitor should glow red.
 
  • Like
Reactions: glockshooter
I adjusted the dip switches. I know your not really supposed to but I turned the first 3 into the off, off, on position so it stopped feeding pellets 20 seconds earlier and now it lights like a champ. I don’t get it.
 
  • Like
Reactions: Mt Bob
I adjusted the dip switches. I know your not really supposed to but I turned the first 3 into the off, off, on position so it stopped feeding pellets 20 seconds earlier and now it lights like a champ. I don’t get it.
Great.Remember,every stove install is different,draft is different.I think I have my harman "startup feed" set different,also.You will know with time.Plus,those little switches collect dirt/dust,same as the "pots" do on harmon boards,which can cause weird problems.Best of luck.
 
  • Like
Reactions: D-mac02
My igniter lasted 7 years in my Accentra, I planned on replacing it over summer but failed to do so. Does anyone sell the Harman igniter via
credit card/ shipping it to house?

THANKS

Yes, I bought my backup at: Woodmans Parts Plus shipped out of NH Google Woodmans stove parts