Wood Gun Center Plug

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.

timberbuilt

Member
Oct 10, 2009
42
Montana
I've been running my WG for about 7 years, ad the center plug is bairly holding together. I've read a couple of threads about people replacing, and they seemed to imply it was important. Can someone help me understand what the importance of the center plug is? SImilar question, what is the EPA plug all about?

Also, I seem to be having trouble keeping the thing going this year. Is there rule of thumb, or other way to know when the the fan is getting weak? I suspect it as a problem, but having a hard time telling for sure. Is there a cheaper way to get the fan than from AHS?
 
The plug is needed to direct the flow through the proper route in order to achieve proper combustion and proper heat transfer to the jacket. It is only there to be able to clean the tube and must be replaced after cleaning.
 
You may just want to do a thorough cleaning. It is possible that the last tube beyond the fan and before the cyclone is partially blocked. Other than that, what makes you think the fan is the issue?

I believe the EPA plug is for when you’re using very dry wood to prevent puffing.


Sent from my iPhone using Tapatalk
 
You may just want to do a thorough cleaning. It is possible that the last tube beyond the fan and before the cyclone is partially blocked. Other than that, what makes you think the fan is the issue?

I believe the EPA plug is for when you’re using very dry wood to prevent puffing.


Sent from my iPhone using Tapatalk
Wrong, The plug is not and never has been referred to as an epa plug. If the plug is out the hot gasses short circuit directly to the fan tunnel without going through the heat exchanger tubes.

Sent from my SM-G900R4 using Tapatalk
 
I understand. I was referring to the OP’s question on what the EPA plug is all about in the original post. Sorry for the confusion, I guess I should have quoted his post for clarification.


Sent from my iPhone using Tapatalk
 
I understand. I was referring to the OP’s question on what the EPA plug is all about in the original post. Sorry for the confusion, I guess I should have quoted his post for clarification.


Sent from my iPhone using Tapatalk
I see now that he's talking about both plugs. I never had any experience with any epa plugs.

Sent from my SM-G900R4 using Tapatalk
 
You've been running 7 years...have you cleaned out the heat exchange area(need to remove fan unit) and area between cyclone and main housing? This is an annual ritual for me and has improved burning a lot along with annual chimney cleaning. I've found that any time I have had a problem with a good burn or excess smoke it's usually because of a blockage somewhere.
Since you suspect something with the fan...does it make noise(may need new bearing(s))? As stated, the "epa" plug is a small plug for the side tube. Since using this I've had very little huffing with my 3+ yr seasoned wood. Just need to remember to alternate from one tube to the other on a regular basis to wear the refractory evenly.
 
  • Like
Reactions: Fred61
You've been running 7 years...have you cleaned out the heat exchange area(need to remove fan unit) and area between cyclone and main housing? This is an annual ritual for me and has improved burning a lot along with annual chimney cleaning.

Out of curiosity, when you pull the fan off do you have to replace the heat shield? I’m afraid of it crumbling and mine is due for cleaning again this year.



Sent from my iPhone using Tapatalk
 
Thanks all for the responses. Per the questions posed:
1) I have never pulled the fan and cleaned the heat exchange area, or the area between the cyclone and main house. I'll have to consider this. Any additional instruction on this would be helpful, unless it's as easy as pulling things apart and cleaning. I often clean the chimney and upper cyclone.
2) The fan is not making any bearing noise. Mainly I thought I remember the fan making more sound (e.g. could hear better from my porch), and my perception that it wasn't burning as good as I think it should. Might all be in my head too...

New question:
- I've never replaced my center plug. It's a bit cracked and really just barely holding together. I would suspect it let's gas pass. Would that cause trouble with my burn?
- Regarding:
You may just want to do a thorough cleaning. It is possible that the last tube beyond the fan and before the cyclone is partially blocked. Other than that, what makes you think the fan is the issue?

I believe the EPA plug is for when you’re using very dry wood to prevent puffing.


Sent from my iPhone using Tapatalk
How do I clean this last tube?
 
Out of curiosity, when you pull the fan off do you have to replace the heat shield? I’m afraid of it crumbling and mine is due for cleaning again this year.



Sent from my iPhone using Tapatalk
You may be able to save the shield but I would have a spare on hand. If it is over 5 yrs old it probably needs to be replaced anyhow. I have replaced mine once and that was when I replaced the bearing.
 
Thanks all for the responses. Per the questions posed:
1) I have never pulled the fan and cleaned the heat exchange area, or the area between the cyclone and main house. I'll have to consider this. Any additional instruction on this would be helpful, unless it's as easy as pulling things apart and cleaning. I often clean the chimney and upper cyclone.
2) The fan is not making any bearing noise. Mainly I thought I remember the fan making more sound (e.g. could hear better from my porch), and my perception that it wasn't burning as good as I think it should. Might all be in my head too...

New question:
- I've never replaced my center plug. It's a bit cracked and really just barely holding together. I would suspect it let's gas pass. Would that cause trouble with my burn?
- Regarding:
How do I clean this last tube?

7 yrs and never cleaned the heat exchanger....wow! You are most likely not running as efficient as you should and I can understand why it's not running well for you this year. It's not hard at all, pull the entire fan assembly including the mounting plate(4 nuts) and use a drill with a bit extension and a wire wheel along with a shop vac and crevice nozzle. The 1st cleaning will be a bear for you with all the crud that most likely has accumulated in there. After that an annual cleaning still takes a while but won't be nearly as bad(I did my 1st cleaning after 3 yrs). Also, clean the lower tube too. you'll be amazed at the difference in not only performance but what all this area looks like w/o the crud on it.

I just replaced the center plug this year, was only missing a small chunk but I'm a bit anal about keeping everything clean and in good condition. I think this pays off in the long run, we heat 2000+ sq ft and also dhw...since 1st burn(beginning of November) we have gone through apprx. 2.75 cords. Hope this helps...........
 
working on my 140 as i type.i put some sheet metal in front of the handle that keeps the board from fall apart.i use # 10 gauge.have to heat the nuts to get them off.remember stove manufactures want to sell parts.the money is in the parts not the stove.
 
Last edited: