Chimney recommendations.

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.

Medic21

Minister of Fire
Feb 26, 2017
1,163
Northern Indiana
Not looking like the boiler will be fully installed until December or January due to replacing a well and a Jeep that kissed a deer this summer. I am thinking about changing the chimney because it has draft issues on warmer days and with a north wind it’s horrible. The picture is looking north. A 4 foot section and roof bracket have been ordered. Will this be enough?

BB4AF873-213C-4B63-8D4E-B588BDCC29C2.jpeg A251725C-D451-4B14-AA04-3FF06CC6E4D9.jpeg
 
2', 10', 3' rule........The chimney must extend at least 3’ above the highest point where it passes through a roof. And at least 2’ higher than any portion of a building within 10′.
 
2', 10', 3' rule........The chimney must extend at least 3’ above the highest point where it passes through a roof. And at least 2’ higher than any portion of a building within 10′.

It actually meets that now. I measured it a couple years ago. I’m thinking, I’m no expert at all, the wind coming over the roof is creating a downdraft to contend with. Am I wrong in thinking this?
 
I'm no expert either. LOL I just know about that rule back when I was looking at different chimney options. hmm, it's probably hard to tell from the photo, but it sure seems like it wouldn't. What pitch is your roof and how much does your current chimney stick above the roof right now?
 
Doing some crude math, on a 5/12 pitch roof, at 10' away you are 4.2' vertically. Which means you need to have at least 6.2' of exposed chimney from the base. If you add another 4', then you should be good.
 
Doing some crude math, on a 5/12 pitch roof, at 10' away you are 4.2' vertically. Which means you need to have at least 6.2' of exposed chimney from the base. If you add another 4', then you should be good.

Lol, I think I may have just measured ten foot after making a 2 foot mark and not two foot above. Math was never my strong suit.
 
Lol, I think I may have just measured ten foot after making a 2 foot mark and not two foot above. Math was never my strong suit.

oops! To me, judging by your photo, you don't look like it's tall enough based on that rule. However, it's hard to tell for sure looking at a photo.
 
@Medic21 are you keeping the Fire Chief?

For the beginning of the season it will still be in the house. After that in the shop. I plan on modifying it once I put it in the shop. I raised the chimney 5 feet to get it above the peak of the roof by one foot. Hopefully that will take care of the north wind problem. Boiler will be installed by end of December. I dug in the pex last week.

I’m going to weld shut the air holes by the door and enlarge the ones across the top. Then I’m going to add an aux secondary air input that will be straight draft. Hopefully that will take care of all the issues.
 
What are you getting for a boiler?

Woodmaster 4400. The only thing I can get local. Staying away from gasification due to needing longer burn times working 24hr shifts.

I got hooked up with free wood. I’ve hauled three semi loads back to my house, all hardwood from the log buyer I haul for. This is all the stuff the mills don’t want from 20’ logs that may be hollow for a portion to the 3 and 4 foot cut offs. I was leery of the amount of wood I’d use but with cutting this in my driveway I’ll survive. I can get anywhere from 1-3 loads a month and even haul the scraps from the woods at the end of the jobs if I want. I figured I’d need 2-3 loads a year. All I’m out is fuel. I took the dump trailer over and loaded out of his yard with the front end loader. Two full loads didn’t make a dent in the pile then one full load of logs.