Measuring Flue Temperature

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
C

ct01r

Member
Nov 10, 2018
73
Eastern Pa.
I've seen references about flue temp's, but don't understand the importance. Is it for efficiency? safety? I have an infra red reader, and have been "playing" with it, but mostly use it for stove temps to measure different kind of wood. Any info would be appreciated. Thanks!

P.S. I tried to do a word search, but couldn't figure it out. Do you'se have a word search option? Thanks again! Curt
 
Knowing flue temp helps. It lets you know if too much or too little heat is heading up the chimney. Too much heat is a waste and too little can mean creosote will condense and build up.
 
I have a magnetic flue thermometer that is 18 inches above the stove outlet. The ideal temperature is between 280 and 500 degrees Fahrenheit.
 
SeanBB said:
I have a magnetic flue thermometer that is 18 inches above the stove outlet.
Click to expand...
Note that this is on single-wall stove pipe. If the stove pipe is double-wall then a probe style thermometer is needed. The probe thermometer will read 1.5x to 2x higher than the surface temp on single wall stove pipe because the probe is directly in the flue gas stream inside the stove pipe. 350-600ºF is a common temp for a probe.
 
Thanks guys! I have single wall stainless. It's been reading under 150 to 200 when I have the damper and air intake closed down (still has enough air leakage going in to keep the stove itself around 300-400 degrees). When I open it up, the stove pipe reads in the 600's on the outside of the pipe with an infra-red reader. I'll keep experimenting for max efficiency. Thanks again! Curt
 
ct01r said:
Thanks guys! I have single wall stainless. It's been reading under 150 to 200 when I have the damper and air intake closed down (still has enough air leakage going in to keep the stove itself around 300-400 degrees). When I open it up, the stove pipe reads in the 600's on the outside of the pipe with an infra-red reader. I'll keep experimenting for max efficiency. Thanks again! Curt
Click to expand...
Ir thermometers can be thrown off by refective surfaces. Get a magnetic thermometer and run a screw through the hole in the middle.

And btw 150 to 200 is pretty low for the outside of single wall pipe if that is accurate. Chances are you are dropping below 212 by the time it reaves the top of the chimney. 600 is to high for the surface of singlewall.
 
Thanks beholler! I try to avoid the shiny spots to shoot so it's more accurate. Good to know on the temperatures. I'll fine tune the stove accordingly.
 
You must log in or register to reply here.

Similar threads

F
How to maintain proper flu temp with overnight burn
Replies
12
Views
952
Classic Wood Stove Forums (prior to approx. 1993)
3650
3650
J
How can I get my stove top temperature up higher without overfiring the flue pipe?
Replies
17
Views
864
Jotul
Wildflush
W
R
Exit Gas temps on alternative stoves?
Replies
6
Views
602
The Hearth Room - Wood Stoves and Fireplaces
rashomon
R
F
Feedback on newbie observations - Flue vs SST; Air wash ignition, temp increase prior to coaling
Replies
2
Views
548
SBI: Century,Drolet,Osburn,Valcourt,Englander
begreen
begreen
E
Strong Draft and Flue Temps
Replies
11
Views
634
Travis Industries: Lopi, Avalon, FPX
EbS-P
EbS-P
Top Bottom
Back