Hi I just got a new RV100 classic. After installing it, I tried to run RDS setup but ran into a problem. The stove fills the fire pot with some pellets then just as the smoke extractor fan and the ignition element turn on, I get an error code "07-Termic" displayed and the stove turns off. The stove is new, never had a fire in it and the thermal sensor tested good. Is there anyone that can help me? The dealer said it will be December before they can look at it. Thanks
Ravelli RV100 classic error code 07
- Thread starter Art1
- Start date
-
Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.
We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.
We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
jerrieric
Feeling the Heat
I bought an rv100c last winter and I had the service guy actually come down and program it correctly for pellet feed a cetera. Installation was free because I paid the price they were asking for it at the store. So I would recommend you have a tech do the initial setup.
Sounds like the thermocouple (temperature sensor in the exhaust) might be bad, or not connected properly. Find the silver metal braid covered wire, maybe the 2 screw terminal connections to the control board are not tight. Also check that the probe end of the cable is properly inserted into the exhaust pipe (right before the exhaust pipe exits the stove cabinet). The probe just pushes thru an orange gasket, so the probe tip is in the exhaust stream.
I looked at the thermocouple in the exhaust tube. All hooked up, wires in place, and it is sending temperature readings. Service tech coming tomorrow hopefully he can fix it. Thanks
Please let us know the outcome. Always trying to learn more about these quirky Ravelli stoves.
Here's the latest. Dealer came out and replaced the thermal sensor, stove still will not run [code 07-Termic]. He ordered a new control board, fingers crossed this will fix it. I will let you know.
Good to hear. Hope it stays running for you. So far knock on wood my Francesca has been operating trouble free, but the season is just starting. Didn’t not make it through its first two seasons without replacing parts.
jerrieric
Feeling the Heat
jerrieric
Feeling the Heat
I have made a couple of purchases over the phone. Very personable folks, and if I recall correctly they will send you prices via email if requested.
jerrieric
Feeling the Heat
Yeah but I like to shop on the internet and people that don't have their prices listed irritate me. I can get the vermiculite at my local dealer but I don't need it now so when time comes to get it I will then do the price dance
grobinson2
Member
Hey Guys, I know this was from a month or so ago but I am a tech and we are a Ravelli dealer. If you need anything feel free to let me know. We have helped people from ME to WA with the Ravelli line of stoves. Certainly don't know it all but so far I have not run into an issue that we could not solve. Now the older EkoTech line of Ravelli thats another story. 
Thanks again,
Glenn
Thanks again,
Glenn
grobinson2
Member
Overall lack of maintenance which of course is not the stoves fault. That said once something fails it is like a wild goose chase finding the issue and then fixing it. The RDS stoves can be problematic as well, (especially the 120 series) but once you know whats going on fixing the issue is much easier.
Thanks again,
Glenn
Thanks again,
Glenn
Hey Guys, I know this was from a month or so ago but I am a tech and we are a Ravelli dealer. If you need anything feel free to let me know. We have helped people from ME to WA with the Ravelli line of stoves. Certainly don't know it all but so far I have not run into an issue that we could not solve. Now the older EkoTech line of Ravelli thats another story.
Thanks again,
Glenn
I need help! I have a ravelli rv80. I am getting the 07 termic code & air flow sensor code. The air flow sensor code has been there for awhile and has worked fine. I have cleaned the sensor and did nothing. I recently had to replace the auger motor too. Been working fine since auger motor was replaced and now this. The auger will not activate and feed any pellets it shuts down after start up and displays code 07 termic. Its supposed to be below zero all next week. No dealers in my area and called a few places and they dont service them. I will need to fix myself. Any help would be greatly appreciated!!
grobinson2
Member
Similar threads
