Harman XXV + Skytech 3301P = Awesome! (Added link + info relative to Harmans suggested method as wel

  • Active since 1995, Hearth.com is THE place on the internet for free information and advice about wood stoves, pellet stoves and other energy saving equipment.

    We strive to provide opinions, articles, discussions and history related to Hearth Products and in a more general sense, energy issues.

    We promote the EFFICIENT, RESPONSIBLE, CLEAN and SAFE use of all fuels, whether renewable or fossil.
  • Super Cedar firestarters 30% discount Use code Hearth2024 Click here
Exactly the same as it would if the room probe was connected.or not with or without the t-stat being there at all.

It is showing what the control board thinks the temperature pot selection is.
 
It is showing what the control board thinks the temperature pot selection is.
So it is reading what the control board is set to (not the Skytech thermostat). This answered my question. Thank you.
 
I would like to add one of these to mine, now if the temp is warmer out it will cycle on and off and the temp swing in the room is 5 or 6 degrees.

Amazon has a 3301p and a 3301p2 the P@ version looks like it is back lit and I don't see much else different. Anyone know if there is anything else different, I like the back lit idea as I usually have the place dimly lit.
 
So question for those who have installed a remote thermostat on your Harman ( I have a P61-A). Are you using the thermostat to throttle down nighttime temps and realizing better pellet efficiency that way? Or is the main draw just more control over the room temp and less variability in the room temp as opposed to relying on the stove to do this alone? Or both...
 
So question for those who have installed a remote thermostat on your Harman ( I have a P61-A). Are you using the thermostat to throttle down nighttime temps and realizing better pellet efficiency that way? Or is the main draw just more control over the room temp and less variability in the room temp as opposed to relying on the stove to do this alone? Or both...
I I use the skytech 3301p thermostat to lower the temp to 64 at night and while we are away during the day and 68 in the morning and night while we are around the house. I also have it set to maintain 68 all day on Saturday and Sunday. I like being able to see what the real setpoint is vs. what the room temp is. Can't see that on the stove control board. I like the quad mt Vernon's thermostat a lot because of this.
 
So question for those who have installed a remote thermostat on your Harman ( I have a P61-A). Are you using the thermostat to throttle down nighttime temps and realizing better pellet efficiency that way? Or is the main draw just more control over the room temp and less variability in the room temp as opposed to relying on the stove to do this alone? Or both...

The only conclusion I've come up with is that there is no "universal" conclusion... My stove is set and forget at 72 most of the time. I will manually change the temp as circumstances dictate (by no more than a couple degrees). My stove is in the basement and I have 1200 sq feet finished downstairs and 1800 upstairs (cord wood stove nights and weekends upstairs). As I see it, I will alway benefit from having some heat trickle upstairs. The main room the stove is in will heat from 62 to 72 in probably 30-45 minutes. If that's all I was after, I would do bigger setbacks. Problem is, the back bedrooms will take half a day to come up to temp and that's not realistic, so larger setbacks will reduce comfort and, ultimately, take a good bit of pellets to bring everything up to equilibrium. So, in my case, set and forget is best.

PS - Was in the 20's today and I used about 3/4+ of a bag in 24 hours, so my heat loss is really low, further justifying leaving the thermo at 72.
 
Thanks for the responses guys.

I I use the skytech 3301p thermostat to lower the temp to 64 at night and while we are away during the day and 68 in the morning and night while we are around the house. I also have it set to maintain 68 all day on Saturday and Sunday. I like being able to see what the real setpoint is vs. what the room temp is. Can't see that on the stove control board. I like the quad mt Vernon's thermostat a lot because of this.

This is exactly what I envisioned doing when considering purchasing the thermostat... but I wasn't sure if it could actually work in practice! It sounds like it can in some circumstances. For the most part, in the cold, I let the stove run to keep a more even temp for more rooms, like ilbcynya. But outside of the coldest times where it is below freezing for several days on end I think I could run my stove like mepellet and realize greater efficiency in my pellet use. Now to try it!
 
Thanks for the responses guys.



This is exactly what I envisioned doing when considering purchasing the thermostat... but I wasn't sure if it could actually work in practice! It sounds like it can in some circumstances. For the most part, in the cold, I let the stove run to keep a more even temp for more rooms, like ilbcynya. But outside of the coldest times where it is below freezing for several days on end I think I could run my stove like mepellet and realize greater efficiency in my pellet use. Now to try it!
good luck and keep us posted!
 
Great thread. Finally bought a thermostat for the Harman today. Got a Lux TX1500U as this one has a swing temp feature along with other nice programmable features. Works slick. We have it mainly to use as a setback at night and heat things up 30 min before we get up in the morning. I found today that it also helps when running the stove in room temp manual as the thermostat is on the other side of the room and not directly affected by the stoves heat convecting when its in idle mode. Even the convection is helping to keep the room warmer longer before the next heat cycle.

My only concern is with overfiring the stove, but I noticed that the convection blower will stay engaged for awhile even after the thermostat is satisfied. Looks like the convection blower runs until the flame dies down. It doesnt turn off as soon as the thermostat opens, so thats good.
 
Ordered a 3301p for our P43 we're getting on Friday. Many thanks to ibcynya for this thread and the "what the harman manual doesn't tell you" thread. Haven't got the stove yet but I already know how I'm going to set it up to run thanks to that info.

Sam
 
  • Like
Reactions: mepellet
Ordered a 3301p for our P43 we're getting on Friday. Many thanks to ibcynya for this thread and the "what the harman manual doesn't tell you" thread. Haven't got the stove yet but I already know how I'm going to set it up to run thanks to that info.

Sam

My pleasure! Enjoy!
 
Ordered a 3301p for our P43 we're getting on Friday. Many thanks to ibcynya for this thread and the "what the harman manual doesn't tell you" thread. Haven't got the stove yet but I already know how I'm going to set it up to run thanks to that info.

Sam
Yes. Lbcynya was instrumental in me learning how my pellet stove operates. Great contributor!
 
Thanks for this thread.
I like the room temp mode and have dug out my 3301P and am looking for some thermastat wiring to wire it up.


I like the Updated control board for the P38.
Room temp mode is much better than the old style..Ramps instead of full on or full off.
And using the 3301p will make best of both.
 
I relize this is an older thread but instead of creating a new one i thought id ask my question here.

Just got my insert a few weeks ago, harman. I am going to connect it to a Tstat but came accross a question.

The Tstat will be located away from the stove set up like the OP outlined. Should I also extend my RSP away from the stove? Its currently in its original position which is inside the left swing door (accentra model).

I think i do or otherwise the RSP may get satisfied prior to the t-stat and turn off the stove before the heat has reached the other room, but i wanted to verify.

Also when putting into Manual Ignite mode can i first put in auto until i get a flame going then just flip the switch?

Any help is appreciated!
 
The Tstat will be located away from the stove set up like the OP outlined. Should I also extend my RSP away from the stove? Its currently in its original position which is inside the left swing door (accentra model).

I think i do or otherwise the RSP may get satisfied prior to the t-stat and turn off the stove before the heat has reached the other room, but i wanted to verify.
If you want to use the wall mounted t-stat exclusively just turn the setting on the stove all the way up so it's always calling for heat. It won't matter where the probe is.

Also when putting into Manual Ignite mode can i first put in auto until i get a flame going then just flip the switch?
As soon as the ignitor light comes you can switch it to manual and it will complete the ignition process.
 
Thanks for the reply!

I understand what your saying about having the heat all up on the stove so its always calling for heat but the probe is zip tied inside the left door (factory placement). Its gets pretty hot in that compartment and i could see hitting max temp inside that door no problem. Im going to pull the stove this weekend and take a look. After thinking about it Im surprised the installer never asked where i wanted the probe. Where it is right now seems to be where the factory would put it for shipping and is not an ideal permenant place.

If I were to extend the probe away from the stove: When I splice the probe wire am i literally just cutting the probe off the end of the existing wire and connectling longer wire and nutting the wires together?
 
You could just get the wire you are going to use and some wire terminals, unplug the original and make an extension to plug into it
 
im thinking of getting one of these this weekend..my question is do you still need the factory room sensor or can i remove that altogether??? also the op says it comes with everything you need but another poster says you need t stat wire...
 
Last edited:
You cannot remove the room sensor completely. The thermostat must be wired in series with the room sensor.
Ron
 
oh got it..you using the skytech 3301p??
 
No I'm using a Hunter 7 day programmable that I picked up at Menards on sale for 10.00. It works just fine.
Ron
 
What is the effective distance you can have the receiver from the transmitter? I know the instructions say 20 ft., but I have a clear path to the transmitter from the receiver of about 25 ft. Also are most using the Skytech 3301P to set back temps when not at home or to keep a room a constant temp? And do you have to program everyday individually or can a default of the temps you want be loaded in each day without doing it manually?
 
it's like a regular programmable thermostat ..set it each day to what ever you want..i have it drop to 63 when nobody is here and have it go to 68 1/2 hour before we get home..house nice and toasty..i can take the remote to the far end of the house and it still works good..my easy chair is about 30 ft from it and it works with no problem.
 
Not sure if there is still somebody here that could help me with my pf120...

I have the furnace for 2 yrs now and always been on an Honeywell T5 thermostat and worked like a charm, but for the last 3 days, I have my status light that blinks 4 times and then the stove does not shutoff, but goes on until it rans out of pellets... did not change anything, any ideas what is gong on?

Tks